Infiniti M35/M45 Y50. Manual — part 935
INTERIOR ROOM LAMP
LT-285
C
D
E
F
G
H
I
J
L
M
A
B
LT
ACTIVE TEST (INT LAMP)
Operation Procedure
1.
Touch “INT LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3.
Touch item to be tested and check operation of the selected item.
4.
During the operation check, touching “BACK” deactivates the operation.
Display Item List
WORK SUPPORT (BATTERY SAVER)
Operation procedure
1.
Select “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2.
Select “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3.
Select “ROOM LAMP TIMER SET” on “SELECT WORK ITEM” screen.
4.
Touch “START”.
5.
Touch “MODE 1” or “MODE 2”.
6.
Touch “CHANGE SETT”.
7.
The setting will be changed and “CUSTOMIZING COMPLETED” will be displayed.
8.
Touch “END”.
Display Item List
DATA MONITOR (BATTERY SAVER)
Operation Procedure
1.
Touch “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2.
Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3.
Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.
4.
When “SELECTION FROM MENU” is selected, touch items to be monitored. When “ALL SIGNALS” is
selected, all the items will be monitored.
5.
Touch “START”.
6.
Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
Test item
Description
INT LAMP
Personal lamps and map lamps can be operated by any ON-OFF operations.
STEP LAMP TEST
Step lamp can be operated by any ON-OFF operations.
Item
Description
CONSULT-II
ROOM LAMP TIMER SET
Interior room lamp battery saver timer setting can be changed.
MODE 1: 30 min.
MODE 2: 60 min.
ALL SIGNALS
Monitors all the signals.
SELECTION FROM MENU
Selects items and monitor them.
LT-286
INTERIOR ROOM LAMP
Display Item List
NOTE:
This item is displayed, but cannot be monitored.
ACTIVE TEST (BATTERY SAVER)
Operation Procedure
1.
Touch “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3.
Touch item to be tested and check operation of the selected item.
4.
During the operation check, touching “BACK” deactivates the operation.
Display Item List
Monitor item
Contents
IGN ON SW
“ON/OFF”
Displays “IGN ON position (ON)/OFF, ACC position (OFF)” judged from the ignition switch
signal.
ACC ON SW
“ON/OFF”
Displays “IGN ACC, ON position (ON)/OFF position (OFF)” status judged from the key
switch signal.
KEY ON SW
“ON/OFF”
Displays “Intelligent Key inserted into key slot (ON)/Intelligent Key removed from key slot
(OFF)” status judged from the key switch signal.
DOOR SW - DR
“ON/OFF”
Displays status of the driver door as judged from the driver door switch signal. (door is open:
ON/door is closed: OFF)
DOOR SW - AS
“ON/OFF”
Displays “door open (ON)/door closed (OFF)” status, determined from passenger door
switch signal.
DOOR SW - RR
“ON/OFF”
Displays “door open (ON)/door closed (OFF)” status, determined from rear door switch RH
signal.
DOOR SW - RL
“ON/OFF”
Displays “door open (ON)/door closed (OFF) ” status, determined from rear door switch LH
signal.
BACK DOOR SW
NOTE
“OFF”
—
CDL LOCK SW
“ON/OFF”
Displays “door locked (ON)/other (OFF) status, determined from central door lock switch
LOCK signal.
CDL UNLOCK SW
“ON/OFF”
Displays “door unlocked (ON)/other (OFF)” status, determined from central door lock switch
UNLOCK signal.
KEY CYL LK – SW
“ON/OFF”
Displays “door locked (ON)” status, determined from key cylinder switch in driver door.
KEY CYL UN – SW
“ON/OFF”
Displays “door unlocked (OFF)” status, determined from key cylinder switch in driver door.
I - KEY LOCK
“ON/OFF”
Displays “locked (ON)/other (OFF)” status, determined from lock signal.
I - KEY UNLOCK
“ON/OFF”
Displays “unlocked (ON)/other (OFF)” status, determined from unlock signal.
TRNK/HAT MNTR
“ON/OFF”
Displays “trunk open (ON)/trunk close (OFF)” status, determined from trunk room lamp
switch.
I - KEY DR UNLK
“ON/OFF”
Displays “ON” when only driver door is unlocked or “OFF” other cases by Intelligent Key or
any door request switch, determined from unlock signal.
I - KEY AS UNLK
“ON/OFF”
Displays “unlocked (ON)/locked (OFF)” states of passenger door by passenger side door
request switch, determined from unlock signal.
Test item
Description
BATTERY SAVER
Personal lamps and map lamps can be operated by any ON-OFF operations.
INTERIOR ROOM LAMP
LT-287
C
D
E
F
G
H
I
J
L
M
A
B
LT
Interior Room Lamp Control Does Not Operate
NKS003T8
1.
SELF-DIAGNOSIS
With CONSULT-II
1.
Select “BCM” on CONSULT-II. Select “BCM” on “SELECT TEST
ITEM” screen.
2.
Select “SELF-DIAG RESULTS” on “SELECT DIAG MODE”
screen.
Without CONSULT-II
GO TO 2.
Self-diagnostic result
NO DTC>>GO TO 2.
CAN
communication>>Check CAN communication system of
BCM. Refer to
PG-30, "Inspection with CONSULT-II
2.
CHECK CIRCUIT BETWEEN EACH SWITCH AND BCM
With CONSULT-II
1.
Select “BCM” on CONSULT-II. Select “INT LAMP” on “SELECT
TEST ITEM” screen.
2.
Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
3.
Make sure switches turn ON-OFF linked with switch operation.
Refer to
for switches and their func-
tions.
Without CONSULT-II
Check each switch. Refer to
.
OK or NG
OK
>> GO TO 3.
NG
>> Inspect malfunctioning switch system. Refer to
.
3.
CHECK CIRCUIT BETWEEN BCM AND LAMP (1)
With CONSULT-II
1.
Set map lamp switch and rear personal lamp switches to DOOR.
2.
Select “BCM” on CONSULT-II. Select “INT LAMP” on “SELECT
TEST ITEM” screen.
3.
Select “ACTIVE TEST” on “SELECT DIAG MODE” screen.
4.
Check map lamps, personal lamps LH and RH operation.
Without CONSULT-II
GO TO 4.
OK or NG
OK
>> Replace BCM. Refer to
BCS-15, "Removal and Installation of BCM"
.
NG
>> GO TO 4.
PKIA7627E
PKIB3532E
Map lamps, personal lamps LH and RH operate
normally.
PKIA6881E
LT-288
INTERIOR ROOM LAMP
4.
CHECK CIRCUIT BETWEEN BCM AND MAP LAMP (2)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and map lamp connector.
3.
Check continuity between BCM harness connector (A) and map
lamp harness connector (B).
OK or NG
OK
>> Replace BCM. Refer to
BCS-15, "Removal and Installa-
. (Reconnect BCM connector and check
the operation of map lamp. If it is faulty, replace BCM.)
NG
>> Repair harness or connector between BCM and map
lamp.
A
B
Continuity
Connector
Terminal Connector
Terminal
M2
48
R54
5
Yes
SKIB4867E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст