Infiniti M35/M45 Y50. Manual — part 686
DTC P1217 ENGINE OVER TEMPERATURE
EC-1217
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
NBS005KU
TBWT1540E
EC-1218
[VK45DE]
DTC P1217 ENGINE OVER TEMPERATURE
TBWT1497E
DTC P1217 ENGINE OVER TEMPERATURE
EC-1219
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Diagnostic Procedure
NBS005KV
1.
CHECK COOLING FAN OPERATION
With CONSULT-II
1.
Turn ignition switch ON.
2.
Perform “FAN DUTY CONTROL” in “ACTIVE TEST” mode with
CONSULT-II.
3.
Make sure that cooling fan speed varies according to the per-
cent.
Without CONSULT-II
1.
Perform IPDM E/R auto active test and check cooling fan motors
operation, refer to
2.
Make sure that cooling fan operates.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 6.
2.
CHECK COOLING SYSTEM FOR LEAK
Apply pressure to the cooling system with a tester, and check if the
pressure drops.
CAUTION:
Higher than the specified pressure may cause radiator damage.
Pressure should not drop.
OK or NG
OK
>> GO TO 3.
NG
>> Check the following for leak. Refer to
●
Hose
●
Radiator
●
Water pump
3.
CHECK RADIATOR CAP
Apply pressure to cap with a tester.
OK or NG
OK
>> GO TO 4.
NG
>> Replace radiator cap.
PBIB2737E
Testing pressure: 157 kPa (1.6 kg/cm
2
, 23 psi)
PBIC1528E
Radiator cap relief pressure:
59 - 98 kPa (0.6 - 1.0 kg/cm
2
, 9 - 14
psi)
SLC755A
EC-1220
[VK45DE]
DTC P1217 ENGINE OVER TEMPERATURE
4.
CHECK THERMOSTAT
Check the following.
●
Thermostat. (Refer to
CO-55, "THERMOSTAT AND WATER CONTROL VALVE"
.)
●
Water control valve. (Refer to
CO-55, "THERMOSTAT AND WATER CONTROL VALVE"
●
Engine coolant temperature sensor. (Refer to
EC-931, "Component Inspection"
OK or NG
OK
>> GO TO 5.
NG
>> Replace malfunctioning component.
5.
CHECK MAIN 13 CAUSES
If the cause cannot be isolated, go to
EC-1223, "Main 13 Causes of Overheating"
.
>> INSPECTION END
6.
CHECK COOLING FAN CONTROL MODULE POWER SUPPLY CIRCUIT-I
1.
Turn ignition switch OFF.
2.
Disconnect cooling fan control module (1) harness connector
E42.
–
: Vehicle front
–
Cooling fan motor-2 (2)
–
Cooling fan motor-1 (3)
3.
Turn ignition switch ON.
4.
Check voltage between cooling fan control module terminal 3
and ground with CONSULT-II or tester.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 12.
7.
CHECK COOLING FAN CONTROL MODULE GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check harness continuity between cooling fan control module terminal 1 and ground.
Refer to wiring diagram.
3.
Also check harness for short to power.
OK or NG
OK
>> GO TO 8.
NG
>> Repair open circuit or short to power in harness or connectors.
PBIB3346E
Voltage: Battery voltage
PBIA9509J
Continuity should exist.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст