Infiniti FX35 / FX45. Manual — part 434
DTC P2101 ELECTRIC THROTTLE CONTROL FUNCTION
EC-497
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Check voltage between ECM terminal 3 and ground under the fol-
lowing conditions with CONSULT-III or tester.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 3.
3.
CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Disconnect IPDM E/R harness connector E8.
4.
Check continuity between ECM terminal 3 and IPDM E/R terminal 42.
Refer to Wiring Diagram.
5.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E64, F65
• Harness for open or short between ECM and IPDM E/R
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT-I
1.
Reconnect all harness connectors disconnected.
2.
Turn ignition switch OFF.
3.
Check voltage between ECM terminal 104 and ground with
CONSULT-III or tester.
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 6.
6.
CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT-II
1.
Disconnect ECM harness connector.
2.
Disconnect IPDM E/R harness connector E9.
3.
Check continuity between ECM terminal 104 and IPDM E/R terminal 47.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 8.
Ignition switch
Voltage
OFF
Approximately 0V
ON
Battery voltage
(11 - 14V)
MBIB0028E
Continuity should exist.
Voltage: Battery voltage
PBIB1171E
Continuity should exist.
EC-498
< SERVICE INFORMATION >
[VQ35DE]
DTC P2101 ELECTRIC THROTTLE CONTROL FUNCTION
NG
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E211, M41
• Harness for open or short between ECM and IPDM E/R
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK FUSE
1.
Disconnect 15A fuse.
2.
Check 15A fuse for blown.
OK or NG
OK
>> GO TO 9.
NG
>> Replace 15A fuse.
9.
CHECK INTERMITTENT INCIDENT
OK or NG
OK
>> Replace IPDM E/R. Refer to
.
NG
>> Repair or replace harness or connectors.
10.
CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN OR SHORT
1.
Turn ignition switch OFF.
2.
Disconnect electric throttle control actuator harness connector.
3.
Disconnect ECM harness connector.
4.
Check harness continuity between the following terminals.
Refer to Wiring Diagram.
5.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 11.
NG
>> Repair or replace.
11.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Remove the intake air duct.
2.
Check if foreign matter is caught between the throttle valve and
the housing.
OK or NG
OK
>> GO TO 12.
NG
>> Remove the foreign matter and clean the electric throttle
control actuator inside.
12.
CHECK THROTTLE CONTROL MOTOR
EC-499, "Component Inspection"
Electric throttle control
actuator terminal
ECM terminal
Continuity
3
5
Should not exist
4
Should exist
6
5
Should exist
4
Should not exist
PBIB1557E
PBIB1556E
DTC P2101 ELECTRIC THROTTLE CONTROL FUNCTION
EC-499
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
OK or NG
OK
>> GO TO 13.
NG
>> GO TO 14.
13.
CHECK INTERMITTENT INCIDENT
OK or NG
OK
>> GO TO 14.
NG
>> Repair or replace harness or connectors.
14.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace the electric throttle control actuator.
2.
EC-85, "Throttle Valve Closed Position Learning"
.
3.
EC-85, "Idle Air Volume Learning"
>> INSPECTION END
Component Inspection
INFOID:0000000001326374
THROTTLE CONTROL MOTOR
1.
Disconnect electric throttle control actuator harness connector.
2.
Check resistance between terminals 3 and 6.
3.
If NG, replace electric throttle control actuator and go to next
step.
4.
EC-85, "Throttle Valve Closed Position Learning"
.
5.
EC-85, "Idle Air Volume Learning"
Removal and Installation
INFOID:0000000001326375
ELECTRIC THROTTLE CONTROL ACTUATOR
Resistance: Approximately 1 - 15
Ω
[at 25
°
C (77
°
F)]
PBIB0095E
EC-500
< SERVICE INFORMATION >
[VQ35DE]
DTC P2118 THROTTLE CONTROL MOTOR
DTC P2118 THROTTLE CONTROL MOTOR
Component Description
INFOID:0000000001326376
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor and it provides feed-
back to the ECM to control the throttle control motor to make the throttle valve opening angle properly in
response to driving condition.
On Board Diagnosis Logic
INFOID:0000000001326377
This self-diagnosis has the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, the ECM enters fail-safe mode and the MIL lights up.
DTC Confirmation Procedure
INFOID:0000000001326378
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
1.
Turn ignition switch ON and wait at least 2 seconds.
2.
Start engine and let it idle for 5 seconds.
3.
Check DTC.
4.
If DTC is detected, go to
.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2118
2118
Throttle control motor
circuit short
ECM detects short in both circuits between
ECM and throttle control motor.
• Harness or connectors
(Throttle control motor circuit is shorted.)
• Electric throttle control actuator
(Throttle control motor)
Engine operating condition in fail-safe mode
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return
spring.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст