Infiniti FX35 / FX45. Manual — part 757
SYSTEM DESCRIPTION
LAN-5
< SERVICE INFORMATION >
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
N
O
P
CAN COMMUNICATION CONTROL CIRCUIT
*: These are the only control units wired with both ends of CAN communication system.
Diag on CAN
INFOID:0000000001451947
DESCRIPTION
“Diag on CAN” is a diagnosis using CAN communication instead of previous DDL1 and DDL2 communication
lines, between control units and diagnosis unit.
SKIB8713E
Component
System description
CAN controller
It controls CAN communication signal transmission and reception, error detection, etc.
Transceiver IC
It converts digital signal into CAN communication signal, and CAN communication signal into digital
signal.
Noise filter
It eliminates noise of CAN communication signal.
Termination circuit
*
(Resistance of approx. 120
Ω
)
It produces potential difference.
LAN-6
< SERVICE INFORMATION >
[CAN FUNDAMENTAL]
SYSTEM DESCRIPTION
System Diagram
SKIB8714E
Name
Harness
Description
DDL1
Tx
Rx
It is used for trouble diagnosis. (CAN-H and CAN-L are used for controlling)
DDL2
K-LINE
It is used for trouble diagnosis. (CAN-H and CAN-L are used for controlling)
Diag on CAN
CAN-H
CAN-L
It is used for trouble diagnosis and control.
TROUBLE DIAGNOSIS
LAN-7
< SERVICE INFORMATION >
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
N
O
P
TROUBLE DIAGNOSIS
Condition of Error Detection
INFOID:0000000001451948
“U1000” or “U1001” is indicated on SELF-DIAG RESULTS on CONSULT-III if CAN communication signal is
not transmitted or received between units for 2 seconds or more.
CAN COMMUNICATION SYSTEM ERROR
• CAN communication line open (CAN-H, CAN-L, or both)
• CAN communication line short (ground, between CAN communication lines, other harnesses)
• Error of CAN communication control circuit of the unit connected to CAN communication line
WHEN “U1000” OR “U1001” IS INDICATED EVEN THOUGH CAN COMMUNICATION SYSTEM IS
NORMAL
• Removal/installation of parts: Error may be detected when removing and installing CAN communication unit
and related parts while turning the ignition switch ON. (A DTC except for CAN communication may be
detected.)
• Fuse blown out (removed): CAN communication of the unit may cease.
• Voltage drop: Error may be detected if voltage drops due to discharged battery when turning the ignition
switch ON (Depending on the control unit which carries out CAN communication).
• Error may be detected if the power supply circuit of the control unit, which carries out CAN communication,
malfunctions (Depending on the control unit which carries out CAN communication).
• Error may be detected if reprogramming is not completed normally.
NOTE:
CAN communication system is normal if “U1000” or “U1001” is indicated on SELF-DIAG RESULTS of CON-
SULT-III under the above conditions. Erase the memory of the self-diagnosis of each unit.
Symptom When Error Occurs in CAN Communication System
INFOID:0000000001451949
In CAN communication system, multiple units mutually transmit and receive signals. Each unit cannot transmit
and receive signals if any error occurs on CAN communication line. Under this condition, multiple control units
related to the root cause malfunction or go into fail-safe mode.
ERROR EXAMPLE
NOTE:
• Each vehicle differs in symptom of each unit under fail-safe mode and CAN communication line wiring.
• Refer to
for the unit abbreviation.
Example: TCM branch line open circuit
SKIB8738E
Unit name
Symptom
ECM
Engine torque limiting is affected, and shift harshness increases.
BCM
Reverse warning chime does not sound.
LAN-8
< SERVICE INFORMATION >
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSIS
Example: Data link connector branch line open circuit
NOTE:
• When data link connector branch line is open, transmission and reception of CAN communication signals
are not affected. Therefore, no symptoms occur. However, be sure to repair malfunctioning circuit.
• When data link connector branch line is open, “ECU list” displayed on the CONSULT-III “CAN DIAG SUP-
PORT MNTR” may be the same as when the CAN communication line has short-circuit. However, symp-
toms differ depending on the case. See below chart for the differences.
EPS control unit
Normal operation.
Combination meter
• Shift position indicator and OD OFF indicator turn OFF.
• Warning lamps turn ON.
ABS actuator and electric unit (control unit)
Normal operation.
TCM
No impact on operation.
IPDM E/R
Normal operation.
Unit name
Symptom
SKIB8739E
Unit name
Symptom
ECM
Normal operation.
BCM
EPS control unit
Combination meter
ABS actuator and electric unit (control unit)
TCM
IPDM E/R
“ECU list” on the “CAN DIAG
SUPPORT MNTR”
(CONSULT-III)
Difference of symptom
Data link connector branch line open circuit
All Diag on CAN units are not
indicated.
Normal operation.
CAN-H, CAN-L harness short-circuit
Most of the units which are connected to the CAN
communication system enter fail-safe mode or are
deactivated.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст