Infiniti FX35 / FX45. Manual — part 667
OIL PAN AND OIL STRAINER
EM-185
< SERVICE INFORMATION >
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Hold pipes and pull them out to front drive shaft (left) installing side.
21. Remove oil strainer.
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSTALLATION
1.
Install oil strainer.
2.
Install axle pipe to oil pan, if removed.
• Lubricate O-ring groove of axle pipe, O-ring, and O-ring joint of
oil pan with new engine oil.
• Right/left O-ring diameters differ from each other. O-ring with
identification paint mark is installed on front drive shaft (left)
installing side.
• Install axle pipe to oil pan from (left) side.
CAUTION:
Insert it with care to prevent O-ring from sliding.
3.
Install oil pan as follows:
a.
Use scraper to remove old liquid gasket from mating surfaces.
• Also remove the old liquid gasket from mating surface of cylinder block.
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Do not scratch or damage the mating surfaces when cleaning off old liquid gasket.
b.
Install new O-rings to oil pump and front cover side.
c.
Apply a continuous bead of liquid gasket with tube presser
(commercial service tool) to the cylinder block mating surfaces
of oil pan to a limited portion as shown in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-44, "Recommended Chemical Product and Sealant"
CAUTION:
Attaching should be done within 5 minutes after coating.
d.
Install oil pan.
CAUTION:
Install avoiding misalignment of O-rings.
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
NOTE:
Tighten mounting bolts No. 1 and 2 in two steps. The numeri-
cal order No. 11 and 17 shown second steps.
• There are three types of mounting bolts. Refer to the following
for locating bolts.
e.
Tighten transmission joint bolts. Refer to
AT-243, "Removal and Installation (AWD Models)"
f.
Install rear plate cover.
4.
Install oil pan drain plug with new drain plug washer.
PBIC2336E
PBIC0195E
M6
×
30 mm (1.18 in)
: 18, 19
M8
×
100 mm (3.94 in)
: 5, 9
M8
×
45 mm (1.77 in)
: Except the above
PBIC0194E
EM-186
< SERVICE INFORMATION >
[VK45DE]
OIL PAN AND OIL STRAINER
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
"Removal and Installation".
5.
Install in the reverse order of removal after this step.
NOTE:
At least 30 minutes after oil pan is installed, pour engine oil.
INSPECTION AFTER INSTALLATION
1.
Check engine oil level and add engine oil. Refer to
2.
Start engine, and check there is no leak of engine oil.
3.
Stop engine and wait for 15 minutes.
4.
Check engine oil level again. Refer to
IGNITION COIL
EM-187
< SERVICE INFORMATION >
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
IGNITION COIL
Component
INFOID:0000000001325780
Removal and Installation
INFOID:0000000001325781
REMOVAL
1.
Remove engine cover with power tool. Refer to
2.
Remove air duct (inlet), air cleaner case and mass air flow sensor assembly, air duct and resonator
assembly. Refer to
.
3.
Disconnect harness connector from ignition coil.
4.
Remove ignition coil.
CAUTION:
Do not shock it.
INSTALLATION
Install in the reverse order of removal.
1.
Ignition coil
2.
Spark plug
3.
Rocker cover (left bank)
PBIC4748J
EM-188
< SERVICE INFORMATION >
[VK45DE]
SPARK PLUG (PLATINUM-TIPPED TYPE)
SPARK PLUG (PLATINUM-TIPPED TYPE)
Component
INFOID:0000000001325782
Removal and Installation
INFOID:0000000001325783
REMOVAL
1.
Remove engine cover with power tool. Refer to
2.
Remove ignition coil. Refer to
.
3.
Remove spark plug with spark plug wrench (commercial service
tool).
CAUTION:
Do not drop or shock it.
INSPECTION AFTER REMOVAL
Use standard type spark plug for normal condition.
Hot type spark plug is suitable when fouling occurs with standard type spark plug under conditions such as:
• Frequent engine starts
• Low ambient temperatures
Cold type spark plug is suitable when spark plug knock occurs with standard type spark plug under conditions such as:
• Extended highway driving
• Frequent high engine revolution
1.
Ignition coil
2.
Spark plug
3.
Rocker cover (left bank)
PBIC4748J
SEM294A
Make
NGK
Standard type
PLFR5A-11
Hot type
PLFR4A-11
Cold type
PLFR6A-11
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст