Infiniti FX35 / FX45. Manual — part 956

AWD CONTROL UNIT

TF-35

< SERVICE INFORMATION >

C

E

F

G

H

I

J

K

L

M

A

B

TF

N

O

P

AWD CONTROL UNIT

Removal and Installation

INFOID:0000000001327456

REMOVAL

1.

Remove the dash side finisher. Refer to

EI-38, "Component Parts Location"

.

2.

Disconnect AWD control unit connector.

3.

Remove the AWD control unit.

INSTALLATION

Install in the reverse order of removal.

SDIA2274E

TF-36

< SERVICE INFORMATION >

FRONT OIL SEAL

FRONT OIL SEAL

Removal and Installation

INFOID:0000000001327457

REMOVAL

1.

Remove the drain plug to drain the transfer fluid. Refer to

TF-10, "Replacement"

.

2.

Remove the front propeller shaft. Refer to

PR-4

.

3.

Remove front oil seal using a flat-bladed screwdriver.

CAUTION:

Be careful not to damage the front case and front drive
shaft.

INSTALLATION

1.

Apply ATF to front oil seal, install it with a drift until the end face
of front case.

CAUTION:

• Do not reuse front oil seal.
• When installing, do not incline front oil seal.

2.

Install front propeller shaft. Refer to

PR-4

.

3.

Install transfer fluid, check fluid level and for fluid leakage. Refer
to

TF-10, "Inspection"

.

SDIA1782E

Tool number

: ST27862000 (

—

)

SDIA1783E

REAR OIL SEAL

TF-37

< SERVICE INFORMATION >

C

E

F

G

H

I

J

K

L

M

A

B

TF

N

O

P

REAR OIL SEAL

Removal and Installation

INFOID:0000000001327458

REMOVAL

1.

Remove the rear propeller shaft. Refer to

PR-7

.

2.

Remove self-lock nut of companion flange using the flange
wrench.

3.

Put matching mark on the end of the mainshaft. The mark
should be in line with the mark on the companion flange.

CAUTION:

For matching mark, use paint. Do not damage mainshaft.

4.

Remove the companion flange using a puller.

CAUTION:

Be careful not to damage the companion flange.

5.

Remove the rear oil seal using a puller.

CAUTION:

Be careful not to damage the rear case.

INSTALLATION

SDIA2454E

SDIA2378E

SDIA1785E

Tool number

: KV381054S0 (J-34286)

SDIA1786E

TF-38

< SERVICE INFORMATION >

REAR OIL SEAL

1.

Apply ATF to rear oil seal, install it with a drift.

CAUTION:

• Do not reuse rear oil seal.
• When installing, do not incline rear oil seal.

2.

Align the matching mark of mainshaft with the mark of compan-
ion flange, then install the companion flange.

3.

Using flange wrench, install the self-lock nut of companion
flange and tighten to the specified torque. Refer to

TF-40, "Dis-

assembly and Assembly"

.

CAUTION:

Do not reuse self-lock nut.

4.

Install the rear propeller shaft. Refer to

PR-7

.

5.

Check fluid level. Refer to

TF-10, "Inspection"

.

Dimension A

: 6.7 - 7.3 mm (0.264 - 0.287 in)

Tool number

A: ST30720000 (J-25405)

B: KV40104830 (

—

)

PDIA0292E

SDIA2378E

PDIA0245E