Infiniti FX35 / FX45. Manual — part 934
SE-94
< SERVICE INFORMATION >
FRONT SEAT
6.
Remove the retainer and clip.
7.
After removing the seat cushion trim and pad, remove the hog rings to separate the trim and pad and the
seat cushion heater unit.
INSTALLATION OF SEAT CUSHION TRIM AND PAD
Install in the reverse order of removal.
PIIA6055E
REAR SEAT
SE-95
< SERVICE INFORMATION >
C
D
E
F
G
H
J
K
L
M
A
B
SE
N
O
P
REAR SEAT
Removal and Installation
INFOID:0000000001328149
PIIB8527E
1.
Headrest (side)
2.
Headrest holder (free)
3.
Headrest holder (locked)
4.
Seatback trim (RH)
5.
Seatback pad (RH)
6.
Seatback frame (RH)
7.
Nut
8.
Seat hinge cover (RH)
9.
Screw
10. Reclining lever (RH)
11. Reclining device outer cover (RH)
12.
Reclining device inner cover (RH)
SE-96
< SERVICE INFORMATION >
REAR SEAT
REMOVAL
1.
Pull the lock at the front bottom of the seat cushion forward (1
for each side), and pull the seat cushion upward to release the
wire from the plastic hook, then pull the seat cushion forward to
remove.
2.
Remove the seatback mounting nuts.
3.
Remove the seatback mounting bolt and nut.
Remove the remote control wire.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After rear wheel house finisher assembly is remove the seatback is installed. Refer to
REMOVAL OF SEAT CUSHION TRIM AND PAD
13. Bolt
14. Seatback garnish (RH)
15.
Trunk net hook
16. Clip (C101)
17. Headrest (center)
18.
Seatback trim (LH)
19. Seatback pad (LH)
20. Seatback frame (LH)
21.
Seatback garnish (LH)
22. Armrest bracket cover
23. Armrest bracket
24.
Armrest
25. Reclining device inner cover (LH)
26. Reclining device outer cover (LH)
27.
Reclining lever (LH)
28. Seat hinge cover (LH)
29. Seat cushion trim
30.
Seat cushion pad
31. Cup holder bracket
32. Cup holder
PIIA6034E
PIIA6035E
PIIA6036E
REAR SEAT
SE-97
< SERVICE INFORMATION >
C
D
E
F
G
H
J
K
L
M
A
B
SE
N
O
P
1.
Remove the cup holder in the back of the seat cushion.
2.
Removal the hog rings to separate the trim and pad.
INSTALLATION OF SEAT CUSHION TRIM AND PAD
Install in the reverse order of removal.
REMOVAL OF SEATBACK TRIM AND PAD
1.
Remove the trunk net hook in the back of the seatback.
2.
After removing the seatback garnish, remove the hog rings.
3.
Remove the headrest.
4.
Remove the headrest holder.
Squeeze and pull up headrest holder tabs to remove from seat-
back frame.
NOTE:
Before installing the headrest holder, check its orientation (front,
rear, left and right).
5.
Remove the armrest (LH only).
6.
After removing the seatback trim and pad, separate the trim and pad.
INSTALLATION OF SEATBACK TRIM AND PAD
Install in the reverse order of removal.
PIIA4985E
PIIA6037E
PIIA1158E
PIIA6038E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст