Infiniti FX35 / FX45. Manual — part 933
SE-90
< SERVICE INFORMATION >
FRONT SEAT
REMOVAL
When removing or installing the seat trim, carefully handle it to keep dirt out and avoid damage.
CAUTION:
• Before removing the front seat, turn ignition switch OFF, disconnect both battery cables and wait at
least 3 minutes.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag to deploy.
• Do not drop, tilt, or bump the side air bag module installing in the seat. Always handle it with care.
1.
Remove the seat cushion outer finisher cover.
2.
Remove the front seat belt anchor bolt. Refer to
and Installation of Front Seat Belt"
CAUTION:
Set the front and rear cushion lifter to the down position.
3.
Remove the screw.
4.
Remove the seat cushion forward finisher lid.
5.
Remove the seat cushion forward finisher.
6.
Remove the seat slide and lifter switch knob (1) and seat reclin-
ing switch knob (2).
1.
Headrest
2.
Headrest holder (free)
3.
Headrest holder (locked)
4.
Seatback pad
5.
Seatback trim
6.
Seat cushion inner finisher
7.
Screw
8.
Seat cushion trim
9.
Seat cushion pad
10. Seatback garnish
11.
Nut
12. Side air bag module
13. Clip (C101)
14. Inner cloth stay
15. Lumber support device
16. Bolt
17. Seatback frame
18. Reclining device assembly
19. Seat cushion frame
20. Seat harness assembly
21. Seat adjust assembly
22. Clip (C103)
23. Seat adjust assembly cover
24. Seat cushion outer finisher
25. Seat cushion outer finisher cover
26. Lumber support switch assembly
27. Seat reclining switch knob
28. Seat slide and lifter switch knob
29. Seat control switch
30. Seat cushion forward finisher
31. Seat cushion forward finisher lid
PIIA6040E
PIIB8525E
FRONT SEAT
SE-91
< SERVICE INFORMATION >
C
D
E
F
G
H
J
K
L
M
A
B
SE
N
O
P
7.
Remove the seat cushion outer finisher.
8.
Remove the seat control switch assembly.
9.
Remove the lumber support switch assembly.
10. Remove the front and rear leg cover (LH and RH).
NOTE:
• Slide the seat backward, and disconnect the front tabs on the
front leg cover. Then move the cover toward the rear of the
vehicle, and pull up to remove.
• Slide the seat forward, then disengage the tabs on the front LH
and RH of the rear leg cover and tabs engaged into the rail.
Then pull the cover toward the rear of the vehicle.
11. Slide the seat until the body mounting bolts are visible and a tool can be inserted.
NOTE:
When disassembling the driver seat after removal, set the front and rear cushion lifter to the top position.
12. Disconnect both battery cables.
13. Remove the harness connector for the side air bag module.
14. Remove the power seat harness connector and vehicle harness fixing clip.
15. Remove the front seat.
NOTE:
When removing and installing, using waste, protect the parts from damage where it may interfere with oth-
ers.
INSTALLATION
Install in the reverse order of removal.
NOTE:
PIIB8526E
1.
Screw
2.
Seat cushion forward finisher
3.
Seat cushion outer finisher
4.
Clip(C101)
5.
Seat control switch
PIIA4984E
SE-92
< SERVICE INFORMATION >
FRONT SEAT
Be sure to insert the rear end tab of the rear leg cover under the rail.
REMOVAL OF SEATBACK TRIM AND PAD
1.
Remove the seatback garnish.
2.
Remove the retainer.
3.
Remove the stay securing the inner cloth.
4.
Remove the headrest.
5.
Remove the headrest holder.
From the back of the seatback, press the headrest holder tab of
the stay pipe hole to disengage. Then pull the headrest holder
up to remove.
NOTE:
Before installing the headrest holder, check its orientation (front,
rear, left and right).
PIIA6041E
PIIA6042E
PIIA6048E
PIIA6050E
FRONT SEAT
SE-93
< SERVICE INFORMATION >
C
D
E
F
G
H
J
K
L
M
A
B
SE
N
O
P
6.
Remove the heated seat connector.
7.
After removing the seatback trim and pad, remove the hog rings to separate the trim, pad, and seatback
heater unit.
INSTALLATION OF SEATBACK TRIM AND PAD
Install in the reverse order of removal.
REMOVAL OF SEAT CUSHION TRIM AND PAD
CAUTION:
Do not disassemble the component parts of only front passenger seat in the dotted lines shown in the
figure. Refer to "Removal and Installation".
1.
Remove the seat cushion inner finisher.
2.
Remove the velcro and retainer.
3.
Remove the seat harness connector.
4.
Remove the seatback frame.
5.
Remove the reclining device assembly.
PIIA6049E
PIIA6052E
PIIA6053E
PIIA6054E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст