Infiniti FX35 / FX45. Manual — part 98
AT-320
< SERVICE INFORMATION >
ASSEMBLY
51. Install needle bearing to front sun gear.
CAUTION:
• Take care with the direction of needle bearing. Refer to
AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
52. Adjust brake band tilting using clips so that brake band contacts
front sun gear drum evenly.
53. Adjust brake band.
a.
Loosen lock nut.
b.
Tighten band servo anchor end pin to the specified torque.
c.
Back of band servo anchor end pin three turns.
d.
Holding band servo anchor end pin, tighten lock nut to the spec-
ified torque. Refer to
.
Adjustment
INFOID:0000000001327411
TOTAL END PLAY
• Measure clearance between front sun gear and bearing race for oil
pump cover.
• Select proper thickness of bearing race so that end play is within
specifications.
SCIA2808E
SCIA5033E
: 5.0 N·m (0.51 kg-m, 44 in-lb)
SCIA5498E
SCIA2810E
ASSEMBLY
AT-321
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
1.
Measure dimensions “K” and “L” and then calculate dimension
“J”.
a.
Measure dimension “K”.
b.
Measure dimension “L”.
c.
Calculate dimension “J”.
2.
Measure dimensions “M
1
” and “M
2
” and then calculate dimen-
sion “M”.
a.
Place bearing race and needle bearing on oil pump assembly.
SCIA7073E
SCIA7074E
“J”
: Distance between oil pump fitting surface of
transmission case and needle bearing mating
surface of front sun gear.
J = K – L
SCIA5352E
SCIA3125E
SCIA3124E
AT-322
< SERVICE INFORMATION >
ASSEMBLY
b.
Measure dimension “M
1
”.
c.
Measure dimension “M
2
”.
d.
Calculate dimension “M”.
3.
Adjust total end play “T
1
”.
• Select proper thickness of bearing race so that total end play
is within specifications. Refer to “Parts Information” for bearing
race selection.
SCIA3126E
SCIA3127E
“M”
: Distance between transmission case fitting
surface of oil pump and needle bearing on oil
pump.
M = M
1
– M
2
SCIA3125E
T
1
= J – M
Total end play “T
1
”
: 0.25 - 0.55 mm (0.0098 - 0.0217 in)
SCIA2810E
ASSEMBLY
AT-323
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
Assembly (2)
INFOID:0000000001327412
1.
Install O-ring to oil pump assembly.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
2.
Install bearing race to oil pump assembly.
CAUTION:
Apply petroleum jelly to bearing race.
3.
Install oil pump assembly in transmission case.
CAUTION:
Apply ATF to oil pump bearing.
4.
Apply recommended sealant (Genuine RTV Silicone Sealant or
equivalent. Refer to
GI-44, "Recommended Chemical Product
.) to oil pump assembly as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
From the oil pump mounting bolts and oil pump mounting
bolt mounting surfaces.
SCIA5172E
SCIA6529E
SCIA2811E
SCIA5321E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст