Infiniti FX35 / FX45. Manual — part 80
AT-248
< SERVICE INFORMATION >
TRANSMISSION ASSEMBLY
• Align the positions of tightening bolts for drive plate with those of
the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts with the specified torque. Refer to "COMPO-
NENTS (FOR VQ35DE)" or "COMPONENTS (FOR VK45DE)".
CAUTION:
• Do not reuse O-ring and copper washers.
• When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
• When tightening the tightening bolts for the torque converter
after fixing the crankshaft pulley bolts, be sure to confirm the
tightening torque of the crankshaft pulley mounting bolts.
Refer to
EM-65, "Removal and Installation"
(for VQ35DE) or
EM-200, "Removal and Installation"
(for VK45DE)
• After converter is installed to drive plate, rotate crankshaft several turns and check to be sure that
transmission rotates freely without binding.
• Install crankshaft position sensor (POS). Refer to
EM-35, "Component (AWD Models)"
(for VQ35DE) or
(for VK45DE).
• After completing installation, check A/T fluid leakage, A/T fluid level, and the positions of A/T. Refer to
AT-207, "Checking of A/T Position"
SCIA2010E
OVERHAUL
AT-249
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
OVERHAUL
Component
INFOID:0000000001327400
VQ35DE models
SCIA8098E
1.
O-ring
2.
Oil pump cover
3.
O-ring
4.
Oil pump housing
5.
Self-sealing bolt
6.
Torque converter
7.
Converter housing
8.
Oil pump housing oil seal
9.
Bearing race
AT-250
< SERVICE INFORMATION >
OVERHAUL
10. Needle bearing
11.
O-ring
12. Front carrier assembly
13. Snap ring
14. Front sun gear
15. 3rd one-way clutch
16. Snap ring
17. Bearing race
18. Needle bearing
19. Seal ring
20. Input clutch assembly
21. Needle bearing
22. Rear internal gear
23. Brake band
24. Mid carrier assembly
25. Needle bearing
26. Bearing race
27. Rear carrier assembly
28. Needle bearing
29. Mid sun gear
30. Seal ring
31. Rear sun gear
32. 1st one-way clutch
33. Snap ring
34. Needle bearing
35. High and low reverse clutch hub
36. Snap ring
37. Bearing race
38. Needle bearing
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to
However, refer to the following symbol for others.
: Apply Genuine RTV silicone sealant or equivalent. Refer to
GI-44, "Recommended Chemical Product and Sealant"
.
OVERHAUL
AT-251
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
VK45DE models
SCIA7984E
1.
O-ring
2.
Oil pump cover
3.
O-ring
4.
Oil pump housing
5.
Self-sealing bolt
6.
Torque converter
7.
Converter housing
8.
Oil pump housing oil seal
9.
Bearing race
10.
Needle bearing
11.
O-ring
12. Front carrier assembly
13.
Needle bearing
14. Snap ring
15. Front sun gear
16.
3rd one-way clutch
17. Snap ring
18. Bearing race
19.
Needle bearing
20. Seal ring
21. Input clutch assembly
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст