Infiniti FX35 / FX45. Manual — part 783
HEADLAMP - XENON TYPE -
LT-27
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
LT
N
O
P
Xenon Headlamp Trouble Diagnosis
INFOID:0000000001328286
1.
CHECK 1: XENON HEADLAMP LIGHTING
Install normal xenon bulb to corresponding xenon bulb headlamp, and check if lamp lights up.
OK or NG
OK
>> Replace xenon bulb.
NG
>> GO TO 2.
2.
CHECK 2: XENON HEADLAMP LIGHTING
Install normal HID control unit to corresponding xenon headlamp, and check if lamp lights up.
OK or NG
OK
>> Replace HID control unit.
NG
>> GO TO 3.
3.
CHECK 3: XENON HEADLAMP LIGHTING
Install normal xenon lamp housing assembly to corresponding xenon headlamp, and check if lamp lights up.
OK or NG
OK
>> Replace xenon headlamp housing assembly. [Malfunction in starter (boosting circuit) in xenon
headlamp housing]
NG
>> INSPECTION END
Aiming Adjustment
INFOID:0000000001328287
PREPARATION BEFORE ADJUSTING
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
1.
Keep all tires inflated to correct pressures.
2.
Place vehicle on level ground.
3.
Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant, engine oil filled up to correct level and full fuel tank.
LOW BEAM AND HIGH BEAM
PKIC9684E
LT-28
< SERVICE INFORMATION >
HEADLAMP - XENON TYPE -
1.
Turn headlamp low beam ON.
CAUTION:
Be sure aiming switch is set to “0” when performing aiming
adjustment.
2.
Use adjusting screws to perform aiming adjustment.
ADJUSTMENT USING AN ADJUSTMENT SCREEN (LIGHT/DARK BORDERLINE)
If the vehicle front body has been repaired and/or headlamp assembly has been replaced, check aiming.
Use the aiming chart shown in the figure.
• Basic illumination area for adjustment should be within the range shown on the aiming chart.
Adjust headlamp accordingly.
Bulb Replacement
INFOID:0000000001328288
HEADLAMP HIGH/LOW BEAM
PKIB3650E
PKIC9731E
HEADLAMP - XENON TYPE -
LT-29
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
LT
N
O
P
1.
Turn lighting switch OFF.
2.
Disconnect the battery cable from the negative terminal or
remove power fuse.
3.
Remove air cleaner case (when replacing LH bulb). Refer to
(VQ35).
4.
Remove radiator reservoir tank (when replacing RH bulb). Refer
to
5.
Turn plastic cap counterclockwise and unlock it.
6.
Turn bulb socket counterclockwise and unlock it.
7.
Unlock retaining spring and remove bulb from headlamp.
8.
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
.
DAYTIME/PARKING LAMP
1.
Turn lighting switch OFF.
2.
Remove air cleaner case (when replacing LH bulb of VK45).
Refer to
.
3.
Turn bulb socket counterclockwise and unlock it.
4.
Remove bulb from its socket.
5.
Installation is the reverse order of removal.
FRONT TURN SIGNAL LAMP
1.
Turn lighting switch OFF.
2.
Turn bulb socket counterclockwise with suitable tool and unlock
it.
3.
Remove bulb from its socket.
4.
Installation is the reverse order of removal.
FRONT SIDE MARKER LAMP
1.
Turn lighting switch OFF.
2.
Turn bulb socket counterclockwise and unlock it.
3.
Remove bulb from its socket.
4.
Installation is the reverse order of removal.
CAUTION:
Headlamp high/low beam (Xenon)
: 12 V - 35 W (D2S)
PKIC9730E
Daytime/Parking lamp
: 12 V - 21/5 W
PKIC9732E
Front turn signal lamp
: 12 V - 21 W (amber)
SKIA6182E
Front side marker lamp
: 12 V - 3.8 W
SKIA5552E
LT-30
< SERVICE INFORMATION >
HEADLAMP - XENON TYPE -
After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertight-
ness.
Removal and Installation
INFOID:0000000001328289
REMOVAL
1.
Disconnect the battery cable from the negative terminal or
remove power fuse.
2.
Remove front bumper fascia assembly. Refer to
3.
Remove headlamp mounting bolts and nut.
4.
Remove plastics bumper bracket, then pull headlamp toward
vehicle front, disconnect connector, and remove headlamp.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Disassembly and Assembly
INFOID:0000000001328290
DISASSEMBLY
1.
Turn plastic cap counterclockwise and unlock it.
SKIA5553E
Headlamp mounting bolt
: 6.1 N·m (0.62 kg-m, 54 in-lb)
1.
Side marker lamp bulb
2.
Side marker lamp bulb socket
3.
Front turn signal lamp bulb socket
4.
Front turn signal lamp bulb
5.
Seal packing
6.
Plastic cap
7.
Xenon bulb (high/low)
8.
Xenon bulb socket (high/low)
9.
HID control unit cover mounting screw
10.
HID control unit cover
11.
HID control unit mounting screw
12.
HID control unit
13.
Seal packing
14.
Daytime/Parking lamp bulb socket
15.
Daytime/Parking lamp bulb
16.
Headlamp housing assembly
17.
Retaining spring
:Alway replace after every disassembly
:N·m (kg-m, in-lb)
PKIC9685E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст