Infiniti FX35 / FX45. Manual — part 331
BASIC SERVICE PROCEDURE
EC-85
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4.
Follow the instruction of CONSULT-III display.
Accelerator Pedal Released Position Learning
INFOID:0000000001325923
DESCRIPTION
Accelerator Pedal Released Position Learning is an operation to learn the fully released position of the accel-
erator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time
harness connector of accelerator pedal position sensor or ECM is disconnected.
OPERATION PROCEDURE
1.
Make sure that accelerator pedal is fully released.
2.
Turn ignition switch ON and wait at least 2 seconds.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Turn ignition switch ON and wait at least 2 seconds.
5.
Turn ignition switch OFF and wait at least 10 seconds.
Throttle Valve Closed Position Learning
INFOID:0000000001325924
DESCRIPTION
Throttle Valve Closed Position Learning is an operation to learn the fully closed position of the throttle valve by
monitoring the throttle position sensor output signal. It must be performed each time harness connector of
electric throttle control actuator or ECM is disconnected.
OPERATION PROCEDURE
1.
Make sure that accelerator pedal is fully released.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.
Idle Air Volume Learning
INFOID:0000000001325925
DESCRIPTION
Idle Air Volume Learning is an operation to learn the idle air volume that keeps each engine within the specific
range. It must be performed under any of the following conditions:
• Each time electric throttle control actuator or ECM is replaced.
• Idle speed or ignition timing is out of specification.
PREPARATION
Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.
• Battery voltage: More than 12.9V (At idle)
• Engine coolant temperature: 70 - 100
°
C (158 - 212
°
F)
• Park/neutral position switch: ON
• Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
On vehicles equipped with daytime light systems, if the parking brake is applied before the engine is
started the headlamp will not be illuminated.
• Steering wheel: Neutral (Straight-ahead position)
• Vehicle speed: Stopped
• Transmission: Warmed-up
- For models with CONSULT-III, drive vehicle until “ATF TEMP SE 1” in “DATA MONITOR” mode of “A/T” sys-
tem indicates less than 0.9V.
- For models without CONSULT-III, drive vehicle for 10 minutes.
OPERATION PROCEDURE
With CONSULT-III
1.
EC-85, "Accelerator Pedal Released Position Learning"
2.
EC-85, "Throttle Valve Closed Position Learning"
.
3.
Start engine and warm it up to normal operating temperature.
EC-86
< SERVICE INFORMATION >
[VQ35DE]
BASIC SERVICE PROCEDURE
4.
Check that all items listed under the topic PREPARATION (previously mentioned) are in good order.
5.
Select “IDLE AIR VOL LEARN” in “WORK SUPPORT” mode.
6.
Touch “START” and wait 20 seconds.
7.
Make sure that “CMPLT” is displayed on CONSULT-III screen. If “CMPLT” is not displayed, Idle Air Vol-
ume Learning will not be carried out successfully. In this case, find the cause of the incident by referring to
the DIAGNOSTIC PROCEDURE below.
8.
Rev up the engine two or three times and make sure that idle speed and ignition timing are within the
specifications.
Without CONSULT-III
NOTE:
• It is better to count the time accurately with a clock.
• It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit has
a malfunction.
1.
EC-85, "Accelerator Pedal Released Position Learning"
2.
EC-85, "Throttle Valve Closed Position Learning"
.
3.
Start engine and warm it up to normal operating temperature.
4.
Check that all items listed under the topic PREPARATION (previously mentioned) are in good order.
5.
Turn ignition switch OFF and wait at least 10 seconds.
6.
Confirm that accelerator pedal is fully released, then turn ignition switch ON and wait 3 seconds.
7.
Repeat the following procedure quickly 5 times within 5 seconds.
a.
Fully depress the accelerator pedal.
b.
Fully release the accelerator pedal.
8.
Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops
blinking and turned ON.
9.
Fully release the accelerator pedal within 3 seconds after the MIL turned ON.
10. Start engine and let it idle.
11. Wait 20 seconds.
12. Rev up the engine two or three times and make sure that idle speed and ignition timing are within the
specifications.
13. If idle speed and ignition timing are not within the specification, Idle Air Volume Learning will not be carried
out successfully. In this case, find the cause of the incident by referring to the DIAGNOSTIC PROCE-
DURE below.
DIAGNOSTIC PROCEDURE
If idle air volume learning cannot be performed successfully, proceed as follows:
ITEM
SPECIFICATION
Idle speed
650
±
50 rpm (in P or N position)
Ignition timing
15
±
5
°
BTDC (in P or N position)
ITEM
SPECIFICATION
Idle speed
650
±
50 rpm (in P or N position)
Ignition timing
15
±
5
°
BTDC (in P or N position)
SEC897C
BASIC SERVICE PROCEDURE
EC-87
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
1.
Check that throttle valve is fully closed.
2.
Check PCV valve operation.
3.
Check that downstream of throttle valve is free from air leakage.
4.
When the above three items check out OK, engine component parts and their installation condi-
tion are questionable. Check and eliminate the cause of the incident.
It is useful to perform
.
5.
If any of the following conditions occur after the engine has started, eliminate the cause of the
incident and perform Idle Air Volume Learning all over again:
• Engine stalls.
• Erroneous idle.
Fuel Pressure Check
INFOID:0000000001325926
FUEL PRESSURE RELEASE
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “FUEL PRESSURE RELEASE” in “WORK SUPPORT” mode with CONSULT-III.
3.
Start engine.
4.
After engine stalls, crank it two or three times to release all fuel pressure.
5.
Turn ignition switch OFF.
Without CONSULT-III
1.
Remove fuel pump fuse located in IPDM E/R.
2.
Start engine.
3.
After engine stalls, crank it two or three times to release all fuel
pressure.
4.
Turn ignition switch OFF.
5.
Reinstall fuel pump fuse after servicing fuel system.
FUEL PRESSURE CHECK
CAUTION:
Before disconnecting fuel line, release fuel pressure from fuel line to eliminate danger.
NOTE:
• Prepare pans or saucers under the disconnected fuel line because the fuel may spill out. The fuel
pressure cannot be completely released because S50 models do not have fuel return system.
• Use Fuel Pressure Gauge Kit (J-44321) to check fuel pressure.
1.
Release fuel pressure to zero. Refer to “FUEL PRESSURE RELEASE”.
2.
Install the inline fuel quick disconnected fitting between fuel
damper and fuel injector tube.
3.
Connect the fuel pressure test gauge (quick connector adapter
hose) to the inline fuel quick disconnected fitting.
4.
Turn ignition switch ON and check for fuel leakage.
5.
Start engine and check for fuel leakage.
6.
Read the indication of fuel pressure gauge.
7.
If result is unsatisfactory, go to next step.
8.
Check the following.
• Fuel hoses and fuel tubes for clogging
• Fuel filter for clogging
PBIB1603E
At idling:
Approximately 350 kPa (3.57 kg/cm
2
, 51 psi)
PBIB1571E
EC-88
< SERVICE INFORMATION >
[VQ35DE]
BASIC SERVICE PROCEDURE
• Fuel pump
• Fuel pressure regulator for clogging
If OK, replace fuel pressure regulator.
If NG, repair or replace.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст