Infiniti FX35 / FX45. Manual — part 959
TRANSFER ASSEMBLY
TF-47
< SERVICE INFORMATION >
C
E
F
G
H
I
J
K
L
M
A
B
TF
N
O
P
Check items below. If necessary, replace them with new ones.
• Contact surfaces of bearing for wear, damage, etc.
• Damage and cracks of case.
Bearing
Check items below. If necessary, replace them with new ones.
• Damage and rough rotation of bearing.
Shaft
Check items below. If necessary, replace them with new one.
• Damage, peeling, dent, uneven wear, bending, etc. of shaft.
Gears and Chain
Check items below. If necessary, replace them with new ones.
• Excessive wear, damage, peeling, etc. of gear and chain.
ASSEMBLY
Front Drive Shaft and Drive Chain
PDIA0293E
PDIA0300E
PDIA0294E
SDIA2365E
TF-48
< SERVICE INFORMATION >
TRANSFER ASSEMBLY
1.
Install front drive shaft front bearing, using drifts.
2.
Install front drive shaft rear bearing, using a drift.
3.
Install drive chain to front drive shaft.
CAUTION:
Identification mark of drive chain should be in the side of
front bearing of front drive shaft.
4.
Install drive chain to mainshaft, and then install tap front drive
shaft with plastic hammer. Press-fit rear bearing of front drive
shaft to rear case.
CAUTION:
Be careful not to tap drive chain.
5.
Install front case to rear case. Refer to "Front case and rear
case".
Mainshaft Assembly
1.
Install needle bearing to mainshaft.
CAUTION:
Apply ATF to periphery of needle bearing.
2.
Install sprocket and electric controlled coupling to mainshaft.
3.
Install spacer to main shaft.
Tool number
: ST33200000 (J-26082)
PDIA0276E
Tool number
: KV38104010 (
—
)
PDIA0277E
PDIA0284E
PDIA0257E
PDIA0273E
TRANSFER ASSEMBLY
TF-49
< SERVICE INFORMATION >
C
E
F
G
H
I
J
K
L
M
A
B
TF
N
O
P
4.
Install snap ring to mainshaft.
CAUTION:
Do not reuse snap ring.
5.
Install mainshaft assembly to rear case, then install front case
and rear case. Refer to "Front case and rear case".
Front Case and Rear Case
1.
Install breather tube, with plastic hammer.
CAUTION:
Pay attention to the direction of breather tube.
2.
Install baffle plate to rear case, and tighten bolt to the specified
torque. Refer to "COMPONENTS".
3.
Install rear bearing to rear case, using a drift.
CAUTION:
Apply ATF to inside of rear bearing.
4.
Install snap ring to rear case.
CAUTION:
Do not reuse snap ring.
SDIA1602E
PDIA0274E
Tool number
: KV38104010 (
—
)
PDIA0275E
PDIA0263E
TF-50
< SERVICE INFORMATION >
TRANSFER ASSEMBLY
5.
Install mainshaft assembly to rear case, using a drift.
CAUTION:
ATF should be applied to contact surface of mainshaft and
rear bearing.
6.
Install O-ring to transfer assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
7.
Install transfer assembly harness connector into rear case.
8.
Install retainer to transfer assembly harness connector.
9.
Hold electric controlled coupling harness (1) with oil cover hold
plate (2), install oil cover (3) to rear case (4), and tighten bolt to
the specified torque. Refer to "COMPONENTS".
CAUTION:
The harness should be guided by a cut portion.
10. Install oil gutter to rear case.
CAUTION:
The tip of oil gutter should be put into rear case groove.
Tool number
: ST35321000 (
—
)
SDIA2368E
SDIA1597E
SDIA3610E
PDIA0261E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст