Infiniti FX35 / FX45. Manual — part 823
LU-4
< SERVICE INFORMATION >
[VQ35DE]
LUBRICATION SYSTEM
LUBRICATION SYSTEM
Lubrication Circuit
INFOID:0000000001325811
System Chart
INFOID:0000000001325812
PBIC1933E
PBIC2071E
ENGINE OIL
LU-5
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
ENGINE OIL
Inspection
INFOID:0000000001325813
ENGINE OIL LEVEL
NOTE:
Before starting engine, put vehicle horizontally and check the engine oil level. If engine is already started, stop
it and allow 10 minutes before checking.
1.
Pull out oil level gauge and wipe it clean.
2.
Insert oil level gauge and make sure the engine oil level is within
the range shown in the figure.
3.
If it is out of range, adjust it.
NOTE:
When checking the engine oil level, insert oil level gauge with its
tip aligned with oil level gauge guide on cylinder head. (In figure,
air cleaner case and air duct are removed.)
ENGINE OIL APPEARANCE
• Check engine oil for white turbidity or heavy contamination.
• If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following areas:
• Oil pans (lower and upper)
• Oil pan drain plug
• Oil pressure switch
• Oil filter
• Oil filter bracket (AWD models)
• Oil cooler
• Water pump cover
• Chain tensioner cover
• Intake valve timing control cover and intake valve timing control solenoid valve
• Mating surface between cylinder head and rocker cover
• Mating surface between front timing chain case and rear timing chain case
• Mating surface between rear timing chain case and cylinder head
• Mating surface between rear timing chain case and cylinder block
• Mating surface between rear timing chain case and oil pan (upper)
• Mating surface between cylinder block and cylinder head
• Crankshaft oil seals (front and rear)
• Camshaft position sensor (PHASE)
OIL PRESSURE CHECK
PBIC3101E
KBIA1343E
LU-6
< SERVICE INFORMATION >
[VQ35DE]
ENGINE OIL
WARNING:
• Be careful not to get burn yourself, as engine oil may be hot.
• Oil pressure check should be done in “Parking position”.
1.
Check the engine oil level. Refer to "ENGINE OIL LEVEL".
2.
Remove front engine undercover with power tool.
3.
Disconnect harness connector at oil pressure sensor, and
remove oil pressure sensor using deep socket (commercial ser-
vice tool).
CAUTION:
Do not drop or shock oil pressure switch.
4.
Install the oil pressure gauge (SST) and hose (SST).
5.
Start the engine and warm it up to normal operating temperature.
6.
Check the engine oil pressure with engine running under no-load.
NOTE:
When the engine oil temperature is low, the engine oil pressure becomes high.
Engine oil pressure [Engine oil temperature at 80
°
C (176
°
F)]
Unit: kPa (kg/cm
2
, psi)
If difference is extreme, check engine oil passage and oil pump for engine oil leaks.
7.
After the inspections, install oil pressure switch as follows:
a.
Remove old liquid gasket adhering to oil pressure switch and the mating surface.
b.
Apply liquid gasket and tighten oil pressure switch to the specification.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-44, "Recommended Chemical Prod-
.
SBIA0452E
SBIA0453E
SLC926
Engine speed
Approximate discharge pressure
Idle speed
More than 98 (1.0, 14)
2,000 rpm
More than 294 (3.0, 43)
ENGINE OIL
LU-7
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
c.
After warming up engine, make sure there is no leakage of engine oil with running engine.
Changing Engine Oil
INFOID:0000000001325814
WARNING:
• Be careful not to get burn yourself, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Remove front engine undercover with power tool.
2.
Warm up the engine, and check for engine oil leakage from engine components. Refer to
3.
Stop the engine and wait for 10 minutes.
4.
Loosen oil filler cap and then remove drain plug.
5.
Drain engine oil.
6.
Install drain plug with new washer. Refer to
EM-30, "Component (2WD Models)"
.
CAUTION:
Be sure to clean drain plug and install with new washer.
7.
Refill with new engine oil.
Engine oil specification and viscosity:
Refer to
Engine oil capacity (Approximate):
Unit:
(US qt, lmp qt)
CAUTION:
• When filling engine oil, do not pull out oil level gauge.
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in engine.
8.
Warm up the engine and check area around drain plug and oil filter for engine oil leakage.
9.
Stop the engine and wait for 10 minutes.
10. Check the engine oil level. Refer to
.
Oil pressure switch:
: 14.8 N·m (1.5 kg-m, 11 ft-lb)
Oil pan drain plug:
: 34.3 N·m (3.5 kg-m, 25 ft-lb)
Drain and refill
With oil filter change
4.7 (5, 4-1/8)
Without oil filter change
4.4 (4-5/8, 3-7/8)
Dry engine (Overhaul)
5.4 (5-3/4, 4-3/4)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст