Infiniti FX35 / FX45. Manual — part 824
LU-8
< SERVICE INFORMATION >
[VQ35DE]
OIL FILTER
OIL FILTER
Removal and Installation
INFOID:0000000001325815
REMOVAL
1.
Remove front engine undercover with power tool.
2.
Using oil filter wrench (SST), remove oil filter.
CAUTION:
• Oil filter is provided with relief valve. Use Genuine Nissan
Oil Filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.
• Do not allow engine oil to adhere to drive belts.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1.
Remove foreign materials adhering to oil filter installation surface.
2.
Apply engine oil to the oil seal contact surface of new oil filter.
3.
Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to the specification.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
SBIA0454E
SBIA0455E
SMA010
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
SMA229B
OIL FILTER
LU-9
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
2.
Start the engine, and check there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
LU-10
< SERVICE INFORMATION >
[VQ35DE]
OIL FILTER BRACKET (AWD)
OIL FILTER BRACKET (AWD)
Component
INFOID:0000000001325816
Removal and Installation
INFOID:0000000001325817
REMOVAL
WARNING:
Be careful not to get burn yourself, as engine oil may be hot.
1.
Remove front engine undercover with power tool.
2.
Using the oil filter wrench [SST: KV10115801 (J38956)], remove oil filter. Refer to
.
CAUTION:
Do not spill engine oil on drive belt.
3.
Remove oil cooler connector bolt, and then oil cooler with water hoses connected.
4.
Disconnect oil temperature sensor and oil pressure switch harness connectors.
5.
Remove oil filter bracket from oil pan (upper).
6.
Remove oil temperature sensor and oil pressure switch from oil filter bracket.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install oil pressure switch and oil temperature sensor as follows:
- Remove old liquid gasket adhering to oil pressure switch and oil filter bracket.
- Apply liquid gasket and install oil pressure switch, and then oil temperature sensor with a new washer.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-44, "Recommended Chemical Product
1.
Oil filter
2.
Connector bolt
3.
Oil cooler
4.
O-ring
5.
Relief valve
6.
Oil filter bracket
7.
Gasket
8.
Oil pressure switch
9.
Oil temperature sensor
10.
Washer
11.
Oil pan (upper)
SBIA0593E
OIL FILTER BRACKET (AWD)
LU-11
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
• Align cutout on oil cooler with protrusion on oil filter bracket. Refer to
LU-13, "Removal and Installation"
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and add engine oil. Refer to
2.
Start the engine, and check there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст