Infiniti FX35 / FX45. Manual — part 93
AT-300
< SERVICE INFORMATION >
REPAIR FOR COMPONENT PARTS
5.
Install needle bearing to high and low reverse clutch hub.
CAUTION:
• Take care with the direction of needle bearing. Refer to
AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
6.
Install high and low reverse clutch hub to mid sun gear assem-
bly.
7.
Using pair of snap ring pliers, install snap ring to mid sun gear
assembly.
CAUTION:
Do not expand snap ring excessively.
8.
Check operation of 1st one-way clutch.
a.
Hold mid sun gear and turn rear sun gear.
b.
Check 1st one-way clutch for correct locking and unlocking
directions.
CAUTION:
If not as shown in the figure, check installation direction of
1st one-way clutch.
9.
Install needle bearing and bearing races to high and low reverse clutch hub.
CAUTION:
• Take care with the direction of needle bearing . Refer to
AT-264, "Location of Adjusting Shims,
Needle Bearings, Thrust Washers and Snap Rings"
.
•
Apply petroleum jelly to needle bearing and bearing races.
SCIA2857E
SCIA2856E
SCIA2855E
SCIA3132E
REPAIR FOR COMPONENT PARTS
AT-301
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
• VQ35DE models
• VK45DE models
High and Low Reverse Clutch
INFOID:0000000001327408
COMPONENTS
VQ35DE models
SCIA2854E
SCIA5238E
SCIA5223E
1.
High and low reverse clutch drum
2.
Driven plate
3.
Retaining plate
4.
Snap ring
5.
Drive plate
6.
Bearing race
AT-302
< SERVICE INFORMATION >
REPAIR FOR COMPONENT PARTS
VK45DE models
DISASSEMBLY
1.
Remove bearing race from high and low reverse clutch drum.
2.
Using a flat-bladed screwdriver, remove snap ring from high and
low reverse clutch drum.
3.
Remove drive plates, driven plates and retaining plate from high
and low reverse clutch drum.
INSPECTION
• Check the following, and replace high and low reverse clutch assembly if necessary.
High and Low Reverse Clutch Snap Ring
• Check for deformation, fatigue or damage.
High and Low Reverse Clutch Drive Plates
• Check facing for burns, cracks or damage.
High and Low Reverse Clutch Retaining Plates and Driven Plates
• Check facing for burns, cracks or damage.
ASSEMBLY
1.
Install drive plates, driven plates and retaining plate in high and low reverse clutch drum.
SCIA5224E
1.
High and low reverse clutch drum
2.
Driven plate
3.
Retaining plate
4.
Snap ring
5.
Drive plate
6.
Bearing race
SCIA5215E
SCIA2868E
REPAIR FOR COMPONENT PARTS
AT-303
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
CAUTION:
Take care with order of plates.
2.
Using a flat-bladed screwdriver, install snap ring in high and low
reverse clutch drum.
3.
Install bearing race to high and low reverse clutch drum.
CAUTION:
• Take care with the direction of needle bearing. Refer to
AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to bearing race.
Direct Clutch
INFOID:0000000001327409
COMPONENTS
VQ35DE models
SCIA2868E
SCIA5215E
SCIA7128E
1.
Direct clutch drum
2.
Driven plate
3.
Retaining plate
4.
Snap ring
5.
Drive plate
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст