Infiniti Q45 (FY33). Manual — part 350
WORK FLOW
CHECK SYSTEM OPERATION.
Check illumination lamp control operation.
(Refer to System Description.)
NG
E
OK
System is OK.
CHECK SWITCH INPUT SIGNAL.
Check the following switches input signal.
I
Door unlock sensor (Driver side) . . . . . . . . . . . . . . . . . . .. Refer to EL-392.
I
Door switch . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to EL-393.
I
Lighting switch (1st) . . . . . . . . . . . . . . . . . . . . . . . ... Refer to EL-394.
I
Key switch (insert) . . . . . . . . . . . . . . . . . . . . . . . . . Refer to EL-395.
I
Ignition key switch (ACC and IGN) . . . . . . . . . . . . . . . . . ... Refer to EL-396.
I
Interior lamp switch . . . . . . . . . . . . . . . . . . . . . . . ... Refer to EL-397.
I
Personal lamp switch . . . . . . . . . . . . . . . . . . . . . . . Refer to EL-397.
OK
E
NG
Repair or replace.
CHECK ILLUMINATION LAMPS.
Check the following illumination lamps.
(Refer to EL-398.)
I
Console lamp
I
Map lamp
I
Footwell lamp
I
Personal lamp
I
Ignition key hole illumination
OK
E
NG
Repair or replace.
Check system again.
GI
MA
EM
LC
EC
FE
AT
PD
FA
RA
BR
ST
RS
BT
HA
IDX
INTERIOR ILLUMINATION CONTROL — IVMS
Trouble Diagnoses (Cont’d)
H
H
H
EL-391
SEL531W
SEL026V
DOOR UNLOCK SENSOR CHECK (DRIVER SIDE)
CHECK DOOR UNLOCK SENSOR
INPUT SIGNAL. (DRIVER SIDE)
CONSULT-II
See “LOCK SIG-DR” in DATA MONITOR
mode.
“LOCK SIG-DR” should be “LOCK”
when lock knob was locked.
-------------------------------------------------------------------------------------------------------------------------------------- OR --------------------------------------------------------------------------------------------------------------------------------------
ON BOARD
Check driver’s side door lock knob opera-
tion in Switch monitor (Mode II) mode.
(Refer to On board Diagnosis, EL-299.)
Refer to wiring diagram in EL-388.
NG
E
OK
Door unlock sensor is OK.
CHECK DOOR UNLOCK SENSOR.
1. Disconnect door lock actuator connec-
tor.
2. Check continuity between door lock
actuator (door unlock sensor) terminals
q
2
and
q
4
.
OK
E
NG
Replace door lock actuator.
Check the following.
I
Harness for open or short between LCU
and door unlock sensor
I
Ground circuit for door unlock sensor
Condition
Continuity
Locked
No
Unlocked
Yes
INTERIOR ILLUMINATION CONTROL — IVMS
Trouble Diagnoses (Cont’d)
H
H
EL-392
SEL527W
DOOR SWITCH CHECK
SEL914U
SEL021V
CHECK DOOR SWITCH INPUT SIGNAL.
CONSULT-II
See “DOOR SW” in DATA MONITOR
mode.
When door is open:
DOOR SW
ON
When door is closed:
DOOR SW
OFF
-------------------------------------------------------------------------------------------------------------------------------------- OR --------------------------------------------------------------------------------------------------------------------------------------
ON BOARD
Check all doors switches in Switch moni-
tor (Mode II) mode.
(Refer to On board Diagnosis, EL-299.)
Refer to wiring diagram in EL-387.
NG
E
OK
Door switch is OK.
CHECK DOOR SWITCH.
1. Disconnect door switch connector.
2. Check continuity between terminals or
switch body ground.
OK
E
NG
Replace door switch.
Check the following.
I
Door switch ground condition (Front
door) or door switch ground circuit (Rear
door)
I
Harness for open or short between door
switch and BCM
Terminals
Condition
Continuity
Front door
switch
q
1
-
Ground
Pressed
No
Released
Yes
Rear door
switch
q
1
-
q
2
Pressed
No
Released
Yes
GI
MA
EM
LC
EC
FE
AT
PD
FA
RA
BR
ST
RS
BT
HA
IDX
INTERIOR ILLUMINATION CONTROL — IVMS
Trouble Diagnoses (Cont’d)
H
H
EL-393
SEL500W
LIGHTING SWITCH (1ST) CHECK
CHECK LIGHTING SWITCH INPUT SIG-
NAL.
CONSULT-II
See “HD/LMP 1ST SW” in DATA MONI-
TOR mode.
When lighting switch is in 1ST or 2ND:
HD/LMP 1ST SW
ON
When lighting switch is OFF:
HD/LMP 1ST SW
OFF
-------------------------------------------------------------------------------------------------------------------------------------- OR --------------------------------------------------------------------------------------------------------------------------------------
ON BOARD
Check lighting switch in Switch monitor
(Mode II) mode.
(Refer to On board Diagnosis, EL-299.)
Refer to wiring diagram in EL-382.
OK
E
NG
Check the following.
I
7.5A fuse [No.
22
,
located in the fuse block
(J/B)]
I
Tail lamp relay
I
Harness for open or
short between fuse and
BCM
I
Harness for open or
short between tail lamp
relay and fuse
Lighting switch (1st) is OK.
INTERIOR ILLUMINATION CONTROL — IVMS
Trouble Diagnoses (Cont’d)
H
EL-394
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст