Infiniti M45 (Y34). Manual — part 724
SIDE OIL SEAL
RFD-9
C
E
F
G
H
I
J
K
L
M
A
B
RFD
SIDE OIL SEAL
PFP:33142
Removal and Installation
ADS0001K
REMOVAL
1.
Remove side flange with the following procedure for press-fitting.
a.
Remove rear wheel sensor. Refer to
BRC-63, "Removal and Installation"
.
b.
Remove drive shaft and axle assembly. Refer to
and
c.
Install axle stand to side flange.
d.
Using a sliding hammer, pull out the side flange.
2.
Remove oil seal using a flat-bladed screwdriver.
INSTALLATION
1.
Apply multi-purpose grease to sealing lips of side oil seal.
2.
Using the drift, press-fit oil seal so that its surface comes face to
face with the end surface of the case.
CAUTION:
●
When installing the oil seal be careful not to get it
inclined.
●
Discard the old oil seal. Always replace with new one.
3.
Install the side flange with the following procedure.
a.
Attach the protector to side oil seal.
b.
After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the pro-
tector.
Tool number A
: KV40104100 ( – )
Tool number B
: ST3623000 (J25840-A)
SDIA1005E
SDIA1036E
Tool number
: KV38100200 (J26233)
SDIA1037E
Tool number
: KV38107900 (J39352)
SDIA0822E
RFD-10
SIDE OIL SEAL
c.
Put suitable drift on the center of side flange, then drive it until
sound changes.
NOTE:
When installation is completed, driving sound of the side flange
turns into a sound which seems to affect the whole final drive.
4.
Confirm that the dimension of the side flange installation (Mea-
surement A) in the illustration comes into the following.
5.
Install the drive shaft and axle assembly. Refer to
and
6.
Align the installing position of the wheel sensor. Refer to
BRC-63, "Removal and Installation"
Measurement A
: Approx. 326 - 328 mm (12.83 - 12.91 in)
SDIA1039E
REAR FINAL DRIVE ASSEMBLY
RFD-11
C
E
F
G
H
I
J
K
L
M
A
B
RFD
REAR FINAL DRIVE ASSEMBLY
PFP:38300
Removal and Installation
ADS0001L
REMOVAL
1.
Remove exhaust center tube with power tool. Refer to
2.
Remove rear cross bar with power tool. Refer to
3.
Remove rear stabilizer bar with power tool. Refer to
.
4.
Remove rear propeller shaft from the final drive. Refer to
PR-5, "Removal and Installation"
5.
Remove rear drive shaft from final drive, then suspend it by wire etc. with power tool.
6.
Remove breather hose from the final drive.
7.
Remove rear wheel sensor. Refer to
8.
Place a transmission jack on the final drive.
CAUTION:
Do not place a transmission jack on the rear cover (aluminum case).
9.
Remove the mounting bolts and nuts connecting to the suspension member, and remove the rear final
drive.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installation, check the final drive oil level. Refer to
MA-21, "Checking Differential Gear Oil"
1.
Breather hose
2.
Gear carrier
3.
Clip
4.
Rear propeller shaft
5.
Washer
6.
Lower stopper
7.
Drive shaft
8.
Rear final drive assembly
9.
Upper stopper
PDIA0882E
RFD-12
REAR FINAL DRIVE ASSEMBLY
Components
ADS0001M
R200 2–PINION
PDIA0087E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст