Infiniti M45 (Y34). Manual — part 723
PREPARATION
RFD-5
C
E
F
G
H
I
J
K
L
M
A
B
RFD
Commercial Service Tools
ADS0001H
ST33290001 (J34286)
Oil seal puller
Removing front oil seal
Differential shim selection (J34309)
Adjusting bearing preload gear height
Tool number (Kent-Moore No.)
Tool name
Description
ZZA0601D
NT134
Power tool
PBIC0190E
RFD-6
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
PFP:00003
NVH Troubleshooting Chart
ADS0001I
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
Re
fe
r to
.
Re
fe
r to
.
Re
fe
r to
.
Re
fe
r to
.
—
Re
fe
r to
.
NV
H i
n
P
R
s
e
c
tio
n
.
N
V
H
in
F
AX,
RAX, FSU
a
n
d
RSU
s
e
c
ti
o
n
s
.
NV
H i
n
W
T
s
e
c
ti
o
n
.
NV
H i
n
W
T
s
e
c
ti
o
n
.
NV
H i
n
R
A
X
s
e
c
tio
n
.
NV
H i
n
B
R
s
e
c
tio
n
.
NV
H i
n
P
S
s
e
c
ti
o
n
.
Possible cause and SUSPECTED PARTS
R
o
ugh gea
r t
o
ot
h
Im
pr
oper
g
ear
c
ont
act
T
oot
h sur
fa
c
es w
o
rn
In
c
o
rr
ect
back
la
s
h
C
o
m
pani
on f
lan
ge exc
e
ssi
ve
r
unou
t
Im
pr
oper
g
ear
o
il
P
R
OPE
LLER SHAFT
A
X
LE AND
SUSPENSION
TI
R
E
S
ROAD W
H
EEL
DRIVE SHAFT
BR
AK
E
S
S
T
EERI
N
G
Symptom
DIFFERENTIAL
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
FRONT OIL SEAL
RFD-7
C
E
F
G
H
I
J
K
L
M
A
B
RFD
FRONT OIL SEAL
PFP:38189
Removal and Installation
ADS0001J
REMOVAL
1.
Remove the propeller shaft. Refer to
PR-5, "Removal and Installation"
2.
Put a mark on the end of the drive pinion corresponding to the C
position mark on the companion flange.
CAUTION:
●
For matching mark, use paint. Never damage drive pin-
ion.
●
The mark C on the final drive companion flange indicates
the maximum vertical runout position.
3.
Using the drive pinion flange wrench, Remove drive pinion nut.
4.
Using the puller, remove the companion flange.
5.
Using the side oil seal puller, remove front oil seal.
INSTALLATION
1.
Apply multi-purpose grease to sealing lips of oil seal. Press front
oil seal into carrier with tool.
CAUTION:
●
When installing the oil seal, be careful not to get it
inclined.
●
Discard the old oil seal. Always replace with new one.
SDIA0963E
Tool number
: KV40104000 ( – )
SDIA1018E
Tool number
: ST33290001 (J34286)
SDIA0485E
Tool number
: ST30720000 (J25405)
SDIA0493E
RFD-8
FRONT OIL SEAL
2.
Align the matching mark of drive pinion with the mark C of com-
panion flange, then install the companion flange.
3.
Apply oil or grease on the screw part of drive pinion and the seating surface of drive pinion nut.
4.
Install drive pinion nut with tool, tighten the nut to the specified torque. Refer to
CAUTION:
The drive pinion nut is not reusable. Never reuse drive pinion nut.
5.
Install propeller shaft. Refer to
PR-5, "Removal and Installation"
.
SDIA0963E
Tool number
: KV40104000 (–)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст