Infiniti M45 (Y34). Manual — part 451
DTC P1147, P1167 HO2S2
EC-493
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P1147, P1167 HO2S2
PFP:226A0
Component Description
ABS002OY
The heated oxygen sensor 2, after three way catalyst (manifold),
monitors the oxygen level in the exhaust gas on each bank.
Even if switching characteristics of the heated oxygen sensor 1 are
shifted, the air-fuel ratio is controlled to stoichiometric, by the signal
from the heated oxygen sensor 2.
This sensor is made of ceramic zirconia. The zirconia generates volt-
age from approximately 1V in richer conditions to 0V in leaner condi-
tions.
Under normal conditions the heated oxygen sensor 2 is not used for
engine control operation.
CONSULT-II Reference Value in Data Monitor Mode
ABS002OZ
Specification data are reference values.
On Board Diagnosis Logic
ABS002P0
The heated oxygen sensor 2 has a much longer switching time
between rich and lean than the heated oxygen sensor 1. The oxygen
storage capacity before the three way catalyst (manifold) causes the
longer switching time. To judge the malfunctions of heated oxygen
sensor 2, ECM monitors whether the maximum voltage of the sensor
is sufficiently high during the various driving condition such as fuel-
cut.
SEF327R
MONITOR ITEM
CONDITION
SPECIFICATION
HO2S2 (B1)
HO2S2 (B2)
●
Warm-up condition
●
After keeping the engine speed
between 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute
under no load
Revving engine from idle up to
3,000 rpm quickly.
0 - 0.3V
←→
Approx. 0.6 - 1.0V
HO2S2 MNTR (B1)
HO2S2 MNTR (B2)
●
Warm-up condition
●
After keeping the engine speed
between 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute
under no load
Revving engine from idle up to
3,000 rpm quickly.
LEAN
←→
RICH
PBIB1154E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1147
1147
(Bank 1)
Heated oxygen sensor 2
maximum voltage monitoring
The maximum voltage from the sensor is
not reached to the specified voltage.
●
Harness or connectors
(The sensor circuit is open or shorted)
●
Heated oxygen sensor 2
●
Fuel pressure
●
Fuel injector
●
Intake air leaks
P1167
1167
(Bank 2)
EC-494
DTC P1147, P1167 HO2S2
DTC Confirmation Procedure
ABS002P1
NOTE:
If DTC confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
TESTING CONDITION:
For better results, perform “DTC WORK SUPPORT” at a temperature of 0 to 30
°
C (32 to 86
°
F).
1.
Turn ignition switch ON and select “DATA MONITOR” mode with
CONSULT-II.
2.
Start engine and warm it up to the normal operating tempera-
ture.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Start engine and keep the engine speed between 3,500 and
4,000 rpm for at least 1 minute under no load.
5.
Let engine idle for 1 minute.
6.
Make sure that “COOLAN TEMP/S” indicates more than 70
°
C
(158
°
F).
If not, warm up engine and go to next step when “COOLAN
TEMP/S” indication reaches to 70
°
C (158
°
F).
7.
Open engine hood.
8.
Select “HO2S2 (B1) P1147” or “HO2S2 (B2) P1167” of “HO2S2” in “DTC WORK SUPPORT” mode with
CONSULT-II.
9.
Start engine and following the instruction of CONSULT-II.
10. Make sure that “OK” is displayed after touching “SELF-DIAG RESULTS”.
If “NG” is displayed, refer to
EC-500, "Diagnostic Procedure"
If “CAN NOT BE DIAGNOSED” is displayed, perform the following.
a.
Turn ignition switch OFF and leave the vehicle in a cool place (soak the vehicle).
b.
Return to step 1.
Overall Function Check
ABS002P2
Use this procedure to check the overall function of the heated oxygen sensor 2 circuit. During this check, a 1st
trip DTC might not be confirmed.
WITH GST
1.
Start engine and warm it up to the normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
4.
Let engine idle for 1 minute.
5.
Set voltmeter probes between ECM terminal 123 [HO2S2 (B1) signal] or 124 [HO2S2 (B2) signal] and
ground.
SEF189Y
PBIB0819E
DTC P1147, P1167 HO2S2
EC-495
C
D
E
F
G
H
I
J
K
L
M
A
EC
6.
Check the voltage when revving up to 4,000 rpm under no load
at least 10 times.
(Depress and release accelerator pedal as soon as possible.)
The voltage should be above 0.58V at least once during this
procedure.
If the voltage can be confirmed in step 6, step 7 is not nec-
essary.
7.
Keep vehicle at idling for 10 minutes, then check the voltage. Or
check the voltage when coasting from 80 km/h (50 MPH) in D
position.
The voltage should be above 0.58V at least once during this
procedure.
8.
EC-500, "Diagnostic Procedure"
PBIB2079E
EC-496
DTC P1147, P1167 HO2S2
Wiring Diagram
ABS002P3
BANK 1
TBWA0276E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст