Infiniti M45 (Y34). Manual — part 452
DTC P1147, P1167 HO2S2
EC-497
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
123
PU
Heated oxygen sensor 2
(bank 1)
[Engine is running]
●
Revving engine from idle up to 3,000 rpm
quickly after the following conditions are met.
–
Warm-up condition
–
Keeping the engine speed between 3,500
and 4,000 rpm for 1 minute and at idle for 1
minute under no load
0 - Approximately 1.0V
EC-498
DTC P1147, P1167 HO2S2
BANK 2
TBWA0277E
DTC P1147, P1167 HO2S2
EC-499
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
124
B
Heated oxygen sensor 2
(bank 2)
[Engine is running]
●
Revving engine from idle up to 3,000 rpm
quickly after the following conditions are met.
–
Warm-up condition
–
Keeping the engine speed between 3,500
and 4,000 rpm for 1 minute and at idle for 1
minute under no load
0 - Approximately 1.0V
EC-500
DTC P1147, P1167 HO2S2
Diagnostic Procedure
ABS002P4
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten two ground screws.
Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace ground connections.
2.
CLEAR THE SELF-LEARNING DATA
With CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Select “SELF-LEARNING CONT” in “WORK SUPPORT” mode
with CONSULT-II.
3.
Clear the self-learning control coefficient by touching “CLEAR”.
4.
Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171 or P0174 detected?
Is it difficult to start engine?
Without CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF.
3.
Disconnect mass air flow sensor harness connector, and restart
and run engine for at least 5 seconds at idle speed.
4.
Stop engine and reconnect mass air flow sensor harness con-
nector.
5.
Make sure DTC P0102 is displayed.
6.
Erase the DTC memory. Refer to
EMISSION-RELATED DIAGNOSTIC INFORMATION"
7.
Make sure DTC P0000 is displayed.
8.
Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171 or P0174 detected?
Is it difficult to start engine?
Yes or No
Yes
>> Perform trouble diagnosis for DTC P0171or P0174. Refer to
.
No
>> GO TO 3.
PBIB1118E
SEF968Y
PBIB1119E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст