Infiniti M45 (Y34). Manual — part 214
REMOTE KEYLESS ENTRY SYSTEM
BL-81
C
D
E
F
G
H
J
K
L
M
A
B
BL
Trunk lid does not open when electronic key trunk opener
button is continuously pressed.
1.First check the trunk opener cancel switch position is
“ON”.
–
2. Check electronic key.
3. Check trunk lid opener cancel switch.
4. Check trunk open signal.
5. Check trunk lid opener actuator.
6. Check key switch.
7. Replace electronic key.
NOTE:
If the result of electronic key check with CONSULT-II is OK,
electronic key is not malfunctioning. Refer to
8. Replace BCM.
–
Hazard reminder does not activate properly when press-
ing lock or unlock button of electronic key.
(Horn reminder is OK.)
1. Check hazard reminder mode*
*: Hazard reminder mode can be changed. First check the
hazard reminder setting.
2. Check hazard function with hazard switch.
3. Check hazard reminder operation.
4. Replace BCM.
–
Horn reminder does not activate properly when pressing
lock button of electronic key.
(Hazard reminder is OK.)
1. Check horn reminder mode*
*: Horn reminder mode can be changed. First check the
horn chirp setting.
2. Check security horn operation.
3. Replace BCM.
–
Panic alarm (horn and headlamp) does not activate when
panic alarm button is continuously pressed.
(All other remote keyless entry system function is OK.)
1. Check electronic key.
2. Check headlamp function.
3. Check key switch.
4. Replace electronic key.
NOTE:
If the result of electronic key check with CONSULT-II is OK,
electronic key is not malfunctioning. Refer to
5. Replace BCM.
–
Keyless power window down (open) operation does not
activate properly.
(All other remote keyless entry system function is OK.)
1. Check power window down operation mode*
*: Power window down operation mode can be changed.
First check the power window down setting.
2. Check power window function.
3. Replace BCM.
–
Auto door lock operation does not activate properly.
(All other remote keyless entry system function is OK.)
1. Replace BCM.
–
Map lamp operation does not activate properly.
1. Check map lamp function.
2. Check door switch.
3. Replace BCM.
–
Symptom
malfunctioning system and reference
Reference
page
BL-82
REMOTE KEYLESS ENTRY SYSTEM
Check Electronic Key
AIS001DZ
1.
CHECK ELECTRONIC KEY
With CONSULT-II
Check Electronic key “LOCK / UNLOCK BUTTON”, “TRUNK BTN-CON” and “PANIC BTN” in “DATA MONI-
TOR” mode with CONSULT-II.
Without CONSULT-II
Check electronic key in “SWITCH MONITOR” mode. Refer to
.
OK or NG
OK
>> Electronic key is OK.
NG
>> GO TO 2.
2.
CHECK ELECTRONIC KEY ID
With CONSULT-II
Check electronic key “ID Code” in “WORK SUPPORT” mode with CONSULT-II.
Refer to
BL-100, "PROCEDURE 2 (WITH CONSULT-II)"
Without CONSULT-II
Check electronic key “ID Code” in “REMOTE CONTROLLER ID SET UP” mode.
Refer to
BL-99, "PROCEDURE 1 (WITHOUT CONSULT-II)"
.
OK or NG
OK
>> Electronic key was not registered.
NG
>>
●
Check multi remote control receiver.
Refer to
BL-94, "Check Remote Keyless Entry Receiver"
●
Check electronic key battery.
Refer to
BL-97, "Electronic Key Battery Replacement"
.
REMOTE KEYLESS ENTRY SYSTEM
BL-83
C
D
E
F
G
H
J
K
L
M
A
B
BL
Check ACC Power
AIS001PY
1.
CHECK ACC POWER
With CONSULT-II
Check ACC power (“ACC ON SW”) in “DATA MONITOR” mode with CONSULT-II.
Without CONSULT-II
Check voltage between BCM connector and ground.
OK or NG
OK
>> ACC power is OK.
NG
>> Check the following.
●
10A fuse [No. 21, located in fuse block (J/B)]
●
Harness for open or short between BCM and fuse.
Monitor item
Condition
ACC ON SW
Ignition switch ACC or ON position
: ON
Ignition switch OFF position
: OFF
PIIA3367E
Item
Connector
Terminal
(Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
BCM
M4
60 (L/OR)
Ground
ACC or ON
Battery voltage
OFF
0
PIIA3438E
BL-84
REMOTE KEYLESS ENTRY SYSTEM
Check Key Switch
AIS001OD
1.
CHECK KEY SWITCH
With CONSULT-II
Check key switch “IGN KEY SW” in “DATA MONITOR” mode with
CONSULT-II.
Without CONSULT-II
Check voltage between BCM connector and ground.
OK or NG
OK
>> Key switch is OK.
NG
>> GO TO 2.
2.
CHECK KEY SWITCH CIRCUIT
1.
Disconnect key switch connector.
2.
Check continuity between BCM connector M4 terminal 69 (PU/W) and key switch connector M64 terminal
4 (PU/W).
3.
Check continuity between BCM connector M4 terminal 69 (PU/
W) and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
Key is inserted in ignition key
cylinder
: IGN KEY SW ON
Key is removed from ignition
key cylinder
: IGN KEY SW OFF
PIIA4243E
Item
Connec-
tor
Terminal
(Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
BCM
M4
69 (PU/W)
Ground
Key is inserted
Battery voltage
Key is removed
0
PIIA2820E
69 (PU/W) – 4 (PU/W)
: Continuity should exist.
69 (PU/W) – Ground
: Continuity should not exist.
PIIA2821E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст