Infiniti M45 (Y34). Manual — part 89
DTC P1843 ATF PRESSURE SWITCH 3
AT-241
D
E
F
G
H
I
J
K
L
M
A
B
AT
3.
CHECK TERMINAL CORD ASSEMBLY
1.
Remove oil pan. Refer to
AT-312, "Control Valve Assembly"
2.
Disconnect A/T unit assembly harness connector and control valve assembly harness connector.
3.
Check continuity between A/T unit assembly harness connector
and control valve assembly harness connector.
4.
If OK, check harness for short to ground and short to power.
OK or NG
OK
>> Replace the control valve assembly. Refer to
AT-312, "Control Valve Assembly"
.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK DTC
Perform DTC confirmation procedure. Refer to
AT-238, "DTC Confirmation Procedure"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 5.
5.
CHECK TCM
1.
Check TCM input/output signal. Refer to
AT-86, "TCM Input/Output Signal Reference Values"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the control valve assembly. Refer to
AT-312, "Control Valve Assembly"
.
NG
>> Repair or replace damaged parts.
Item
Connector No.
Terminal No. (Wire color)
Continuity
A/T unit assembly
harness connector
F26
2 (R)
Yes
Control valve assem-
bly harness connector
F302
10 (R)
A/T unit assembly
harness connector
F26
7 (W)
Yes
Control valve assem-
bly harness connector
F302
15 (W)
SCIA3100E
AT-242
DTC P1845 ATF PRESSURE SWITCH 5
DTC P1845 ATF PRESSURE SWITCH 5
PFP:25240
Description
ACS004B4
Fail-safe function to detect direct clutch solenoid valve condition.
CONSULT-II Reference Value
ACS004PT
On Board Diagnosis Logic
ACS004B5
●
This is not an OBD-II self-diagnostic item.
●
Diagnostic trouble code “ATF PRES SW 5/CIRC” with CONSULT-II is detected, when TCM detects that
actual gear ratio is normal, and relation between gear position and condition of ATF pressure switch 5 is
irregular during depressing accelerator pedal. (Other than during shift change)
Possible Cause
ACS004B6
●
ATF pressure switch 5
●
Harness or connectors
(The switch circuit is open or shorted.)
DTC Confirmation Procedure
ACS004B7
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1.
Start engine.
2.
Accelerate vehicle to maintain the following condition.
ACCELE POS: 1.5/8 - 2.0/8
Selector lever: “D” position
Gear position: 1st
Þ
2nd Gear (D/C ON/OFF)
3.
Perform step “2” again.
4.
Turn ignition switch OFF, then perform step “1” to “3” again.
5.
Check “SELF-DIAG RESULTS” mode for “A/T” with CONSULT-
II.
If DTC (P1845) is detected, go to
.
If DTC (P1762) is detected, go to
AT-201, "Diagnostic Procedure"
Item name
Condition
Display value
ATF PRES SW 5
Direct clutch solenoid valve operates.
OFF
Other conditions
ON
SAT014K
DTC P1845 ATF PRESSURE SWITCH 5
AT-243
D
E
F
G
H
I
J
K
L
M
A
B
AT
Wiring Diagram — AT — FPSW5
ACS004B8
TCWA0138E
AT-244
DTC P1845 ATF PRESSURE SWITCH 5
TCM terminals and data are reference value.
Diagnostic Procedure
ACS004B9
1.
CHECK INPUT SIGNALS
With CONSULT-II
1.
Start engine.
2.
Select “ECU INPUT SIGNALS” or “MAIN SIGNALS” in “DATA
MONITOR” mode for “A/T” with CONSULT-II.
3.
Accelerate vehicle in “D” position (1st
Þ
2nd gear), and confirm
the ON/OFF actuation of the “ATF PRES SW 5”.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 2.
2.
CHECK HARNESS BETWEEN TCM AND A/T UNIT ASSEMBLY HARNESS CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between A/T unit assembly harness connector
and TCM connector.
4.
If OK, check harness for short to ground and short to power.
5.
Reinstall any part removed.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
Terminal
No.
Wire
color
Item
Condition
Data (Approx.)
22
P/B
SEL2 (ATF pres-
sure switch 5)
–
–
40
Y/G
DATA BIT1
–
–
Item name
Condition
Display value
ATF PRES SW 5
Direct clutch solenoid
valve operates.
OFF
Other conditions
ON
PCIA0067E
Item
Connector No.
Terminal No.
(Wire color)
Continuity
TCM
F103
22 (P/B)
Yes
A/T unit assembly harness
connector
F26
6 (P/B)
TCM
F104
40 (Y/G)
Yes
A/T unit assembly harness
connector
F26
2 (Y/G)
SCIA3101E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст