Infiniti M45 (Y34). Manual — part 735
PRECAUTIONS
SB-3
C
D
E
F
G
I
J
K
L
M
A
B
SB
●
The front seat belt pre-tensioner should be replaced even if the seat belts are not in use during the colli-
sion in which the air bags are deployed.
SB-4
SEAT BELTS
SEAT BELTS
PFP:86884
System Description
AHS0009G
SEAT BELT WARNING CHIME
●
With ignition switch turned ON and seat belt unfastened (seat belt switch ON), warning chime will sound
for approximately 6 seconds.
●
If warning chime does not sound, refer to
DI-62, "Seat Belt Buckle Switch Inspection"
.
SEAT BELT WARNING LAMP
●
Fasten driver's seat belt.
●
The seat belt warning lamp should go out.
●
If the seat belt warning lamp does not go out, refer to
DI-29, "Wiring Diagram — WARN —"
Removal and Installation of Front Seat Belt
AHS0009H
CAUTION:
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least 3
minutes.
REMOVAL OF SEAT BELT RETRACTOR
1.
Remove the adjuster cover on the seat belt shoulder anchor.
2.
Remove the shoulder anchor bolt.
3.
Slide up outer anchor cover, and remove the anchor bolt.
4.
Remove the center pillar upper and lower finisher. Refer to
1.
Seat belt pre-tensioner connector
2.
Retractor
3.
Fiber washer
4.
Plain washer
5.
Plastic washer
6.
Spring washer
7.
Outer anchor
8.
Fiber washer
9.
Seat belt adjuster
10. Adjuster cover
11.
Retaining washer
12. Spacer
13. Spring washer
14. Plain washer
15. Shoulder anchor
PHIA0692E
SEAT BELTS
SB-5
C
D
E
F
G
I
J
K
L
M
A
B
SB
5.
Disconnect the front seat belt pre-tensioner connector.
CAUTION:
●
For installing/removing pre-tensioner seat belt connec-
tor, insert thin screwdriver wrapped in tape into notch, lift
lock and remove connector.
●
Install connector with lock raised, and push lock into
connector.
6.
Remove the front seat belt pre-tensioner retractor fixing screw and then remove the seat belt retractor.
INSTALLATION OF SEAT BELT RETRACTOR
CAUTION:
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least 3
minutes.
Install in the reverse order of removal.
REMOVAL OF SEAT BELT BUCKLE
1.
Remove the front seat. Refer to
.
2.
Remove the screws, and remove the seat cushion inner finisher.
Refer to
SE-127, "Removal and Installation"
.
3.
Disconnect harness connector remove the anchor bolt, and
remove the buckle.
INSTALLATION OF SEAT BELT BUCKLE
Install in the reverse order of removal.
PHIA0341E
PHIA0235E
SB-6
SEAT BELTS
Removal and Installation of Rear Seat Belt
AHS0009I
REMOVAL
1.
Remove the rear seat. Refer to
SE-133, "Removal and Installation"
2.
Remove the rear pillar finisher upper. Refer to
3.
Remove the rear parcel shelf finisher. Refer to
EI-37, "REAR PARCEL SHELF FINISHER"
4.
Remove the outer and inner anchor bolt.
5.
Remove seat belt retractor mounting anchor bolt, and remove the seat belt assembly.
INSTALLATION
Install in the reverse order of removal.
1.
Plain washer
2.
Outer anchor
3.
Fiber washer
4.
Inner anchor (upper)
5.
Inner anchor (lower)
PHIA0693E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст