Infiniti M45 (Y34). Manual — part 789
FRONT PASSENGER AIR BAG MODULE
SRS-43
C
D
E
F
G
I
J
K
L
M
A
B
SRS
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Always work from the side of or under front passenger air bag module.
●
After the work is completed, perform self-diagnosis to check that no malfunction is detected.
Refer to
TORX bolt (size: T50):
: 19.6 N·m (2.0 kg-m, 14.5 ft-lb)
Hex bolt:
: 24.5 N·m (2.5 kg-m, 18 ft-lb)
SRS-44
FRONT SIDE AIR BAG MODULE
FRONT SIDE AIR BAG MODULE
PFP:K8EH0
Removal and Installation
AHS00098
REMOVAL
WARNING:
Removal of front side air bag module should only be done to allow deployment of front side air bag
module prior to disposal of seatback assembly.
Only complete seatback assemblies can be replaced. Refer to
CAUTION:
●
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
●
Always work from the rear of the front side air bag module.
1.
Remove the driver and/or passenger seat. Refer to
.
2.
Remove the seatback board, and remove the retainers securing the seat cushion trim. Refer to
3.
Remove the seatback trim and pad. Refer to
SE-131, "SEATBACK TRIM AND PAD"
.
4.
Remove air bag module harness clips.
5.
Remove the special fasteners coated with bonding agent from
the front side air bag module, and remove the front side air bag
module.
CAUTION:
●
Always place the front side air bag module standing with
the stud bolt side facing down.
●
Do not insert any foreign objects (screwdrivers) into front
side air bag module.
●
Do not attempt to disassemble front side air bag module.
●
Replace front seatback assembly (side air bag module) if it
has been dropped or sustained an impact.
●
Do not expose front seatback assembly (side air bag mod-
ule) to temperatures exceeding 90
°
C (194
°
F).
●
Do not allow oil, grease or water to come in contact with the
front side air bag module.
●
After front side air bag module inflates, front seatback
assembly must be replaced.
PHIA0168E
PHIA0169E
SBF814E
FRONT SIDE AIR BAG MODULE
SRS-45
C
D
E
F
G
I
J
K
L
M
A
B
SRS
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Always work from the rear of the front side air bag module.
●
After the work is completed, perform self-diagnosis to make sure that no malfunction is detected.
Refer to
SRS-46
SIDE CURTAIN AIR BAG MODULE
SIDE CURTAIN AIR BAG MODULE
PFP:985P0
Removal and Installation
AHS0008Y
REMOVAL
CAUTION:
●
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
●
Always work from the side of the side curtain air bag module.
1.
Remove headlining. Refer to
2.
Disconnect side curtain air bag connector.
3.
Remove side curtain air bag module fixing bolts and clip.
4.
Remove the side curtain air bag module.
CAUTION:
●
Always place the side curtain air bag module with the warn-
ing label facing upward.
●
Do not attempt to disassemble side curtain air bag module.
●
Do not insert any foreign objects (screwdriver, etc.) into air
bag module connector.
●
Replace side curtain air bag module if it has been dropped
or sustained an impact.
●
Do not expose the air bag module to temperatures exceed-
ing 90
°
C (194
°
F).
●
Do not allow oil, grease or water to come in contact with the
side curtain air bag module.
PHIA0668E
1.
Side curtain air bag inflator
2.
Side curtain air bag
3.
Bolt
PHIA0216E
SBF814E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст