Infiniti M45 (Y34). Manual — part 460
DTC P1226 TP SENSOR
EC-529
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P1226 TP SENSOR
PFP:16119
Component Description
ABS002Q4
Electric throttle control actuator consists of throttle control motor,
acceleration pedal position sensor, throttle position sensor, etc. The
throttle position sensor responds to the throttle valve movement.
The throttle position sensor has the two sensors. These sensors are
a kind of potentiometers which transform the throttle valve position
into output voltage, and emit the voltage signal to the ECM. In addi-
tion, these sensors detect the opening and closing speed of the
throttle valve and feed the voltage signals to the ECM. The ECM
judges the current opening angle of the throttle valve from these sig-
nals and the ECM controls the throttle control motor to make the
throttle valve opening angle properly in response to driving condi-
tion.
On Board Diagnosis Logic
ABS002Q5
The MIL will not light up for this diagnosis.
DTC Confirmation Procedure
ABS002Q6
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10V at idle.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Turn ignition switch ON.
5.
Repeat steps 3 and 4 for 32 times.
6.
If 1st trip DTC is detected, go to
EC-530, "Diagnostic Procedure"
.
WITH GST
Follow the procedure WITH CONSULT-II above.
PBIB0145E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1226
1226
Closed throttle position
learning performance
problem
Closed throttle position learning is not performed
successfully, repeatedly.
●
Electric throttle control actuator
(TP sensor 1 and 2)
SEF058Y
EC-530
DTC P1226 TP SENSOR
Diagnostic Procedure
ABS002Q7
1.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Turn ignition switch OFF.
2.
Remove the intake air duct.
3.
Check if foreign matter is caught between the throttle valve and
the housing.
OK or NG
OK
>> GO TO 2.
NG
>> Remove the foreign matter and clean the electric throttle
control actuator inside.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace the electric throttle control actuator.
2.
Perform
EC-44, "Accelerator Pedal Released Position Learning"
.
3.
Perform
EC-44, "Throttle Valve Closed Position Learning"
4.
Perform
EC-44, "Idle Air Volume Learning"
>> INSPECTION END
Removal and Installation
ABS002Q8
ELECTRIC THROTTLE CONTROL ACTUATOR
Refer to
PBIB0083E
DTC P1229 SENSOR POWER SUPPLY
EC-531
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P1229 SENSOR POWER SUPPLY
PFP:16119
On Board Diagnosis Logic
ABS002Q9
This self-diagnosis has the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, ECM enters fail-safe mode and the MIL lights up.
DTC Confirmation Procedure
ABS002QA
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10V at idle.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for 1 second.
4.
EC-533, "Diagnostic Procedure"
.
WITH GST
Follow the procedure WITH CONSULT-II above.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P1229
1229
Sensor power supply
circuit short
ECM detects a voltage of power source for
sensor is excessively low or high.
●
Harness or connectors
(The TP sensor 1 and 2 circuit is shorted.)
(APP sensor 1 circuit is shorted.)
(MAF sensor circuit is shorted.)
(EVAP control system pressure sensor circuit
is shorted.)
(Power steering pressure sensor circuit is
shorted.)
(Refrigerant pressure sensor circuit is
shorted.)
●
Electric throttle control actuator
(TP sensor 1 and 2)
●
Accelerator pedal position sensor
(APP sensor 1)
●
MAF sensor
●
EVAP control system pressure sensor
●
Power steering pressures sensor
●
Refrigerant pressures sensor
Engine operation condition in fail-safe mode
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return
spring.
SEF058Y
EC-532
DTC P1229 SENSOR POWER SUPPLY
Wiring Diagram
ABS002QB
TBWA0301E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст