Infiniti M45 (Y34). Manual — part 418
DTC P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-361
C
D
E
F
G
H
I
J
K
L
M
A
EC
12.
CHECK INTERMITTENT INCIDENT
Refer to
EC-132, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END
Component Inspection
ABS002KU
EVAP CONTROL SYSTEM PRESSURE SENSOR
1.
Remove EVAP control system pressure sensor with its harness connector connected.
2.
Remove hose from EVAP control system pressure sensor.
3.
Install a vacuum pump to EVAP control system pressure sensor.
4.
Turn ignition switch ON.
5.
Use pump to apply vacuum and pressure to EVAP control sys-
tem pressure sensor as shown in figure.
CAUTION:
●
Always calibrate the vacuum pump gauge when using it.
●
Do not apply below -93.3 kPa (-700 mmHg, -27.56 inHg) or
pressure over 101.3 kPa (760 mmHg, 29.92 inHg).
6.
Check voltage between ECM terminal 110 and ground with
CONSULT-II or tester.
CAUTION:
Discard any EVAP control system pressure sensor which has dropped from a height of more than
0.5 m (19.7 in) onto a hard surface such a concrete floor; use a new one.
7.
If NG, replace EVAP control system pressure sensor.
Applied vacuum kPa
(mmHg, inHg)
Voltage V
Not applied
1.8 - 4.8
-26.7 (-200 mmHg, -7.87)
2.1 to 2.5V lower than above value
PBIB0156E
EC-362
DTC P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
DTC P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
PFP:25085
Component Description
ABS002KV
The EVAP control system pressure sensor detects pressure in the purge line. The sensor output voltage to the
ECM increases as pressure increases.
CONSULT-II Reference Value in Data Monitor Mode
ABS002KW
Specification data are reference values.
On Board Diagnosis Logic
ABS002KX
NOTE:
If DTC P0453 is displayed with DTC P1229, first perform the trouble diagnosis for DTC P1229.
Refer to
PBIB0026E
PBIB1207E
MONITOR ITEM
CONDITION
SPECIFICATION
EVAP SYS PRES
●
Ignition switch: ON
Approx. 1.8 - 4.8V
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0453
0453
EVAP control system pressure
sensor high input
An excessively high voltage from the
sensor is sent to ECM.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
EVAP control system pressure sensor
●
EVAP canister vent control valve
●
EVAP canister
●
Water separator
●
Rubber hose from EVAP canister vent
control valve to water separator
DTC P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-363
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC Confirmation Procedure
ABS002KY
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Always perform test at a temperature of more than 5
°
C (41
°
F).
WITH CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Select “DATA MONITOR” mode with CONSULT-II.
5.
Make sure that “FUEL T/TEMP SE” is more than 0
°
C (32
°
F).
6.
Wait at least 10 seconds.
7.
If 1st trip DTC is detected, go to
EC-365, "Diagnostic Procedure"
.
WITH GST
1.
Start engine and warm it up to normal operating temperature.
2.
Check that voltage between ECM terminal 92 (Fuel tank temper-
ature sensor signal) and ground is less than 4.2V.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Wait at least 10 seconds.
5.
Select “MODE 7” with GST.
If 1st trip DTC is detected, go to
EC-365, "Diagnostic Procedure"
.
SEF194Y
SEF340X
EC-364
DTC P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
Wiring Diagram
ABS002KZ
TBWA0292E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст