Infiniti QX4 (R50). Manual — part 277
SEF013Z
11) Make sure the following.
Condition
VENT CONTROL/V
Air passage continuity
between A and B
ON
No
OFF
Yes
If the result is NG, go to “Diagnostic Procedure”, EC-577.
If the result is OK, go to “Diagnostic Procedure” for DTC
P0440, EC-355.
AEC783A
Overall Function Check
NBEC0343
Use this procedure to check the overall function of the EVAP can-
ister vent control valve circuit. During this check, a DTC might not
be confirmed.
WITH GST
NBEC0343S01
1)
Disconnect hose from water separator.
2)
Disconnect EVAP canister vent control valve harness connec-
tor.
3)
Verify the following.
Condition
Air passage continuity
12V direct current supply between ter-
minals 1 and 2
No
No supply
Yes
If the result is NG, go to “Diagnostic Procedure”, EC-577.
If the result is OK, go to “Diagnostic Procedure” for DTC
P0440, EC-355.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P1448 EVAPORATIVE EMISSION (EVAP) CANISTER VENT CONTROL
VALVE (OPEN)
DTC Confirmation Procedure (Cont’d)
EC-575
Wiring Diagram
NBEC0344
MEC963C
DTC P1448 EVAPORATIVE EMISSION (EVAP) CANISTER VENT CONTROL
VALVE (OPEN)
Wiring Diagram
EC-576
Diagnostic Procedure
NBEC0345
1
CHECK RUBBER TUBE
1. Turn ignition switch “OFF”.
2. Disconnect rubber tube connected to EVAP canister vent control valve.
3. Check the rubber tube for clogging.
SEF143S
OK or NG
OK
©
GO TO 2.
NG
©
Clean rubber tube using an air blower.
2
CHECK EVAP CANISTER VENT CONTROL VALVE-I
1. Remove EVAP canister vent control valve from EVAP canister.
2. Check portion B of EVAP canister vent control valve for being rusted.
SEF337X
OK or NG
OK
©
GO TO 3.
NG
©
Replace EVAP canister vent control valve.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P1448 EVAPORATIVE EMISSION (EVAP) CANISTER VENT CONTROL
VALVE (OPEN)
Diagnostic Procedure
EC-577
3
CHECK EVAP CANISTER VENT CONTROL VALVE-II
With CONSULT-II
1. Turn ignition switch ON.
2. Perform “VENT CONTROL/V” in “ACTIVE TEST” mode.
3. Check air passage continuity and operation delay time.
SEF991Y
Without CONSULT-II
Check air passage continuity and operation delay time under the following conditions.
SEF339X
Make sure new O-ring is installed properly.
OK or NG
OK
©
GO TO 5.
NG
©
GO TO 4.
4
CHECK EVAP CANISTER VENT CONTROL VALVE-III
1. Clean the air passage (Portion A to B) of EVAP canister vent control valve using an air blower.
2. Perform Test No. 3 again.
OK or NG
OK
©
GO TO 5.
NG
©
Replace EVAP canister vent control valve.
DTC P1448 EVAPORATIVE EMISSION (EVAP) CANISTER VENT CONTROL
VALVE (OPEN)
Diagnostic Procedure (Cont’d)
EC-578
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст