Infiniti Q45. Manual — part 544
SUNSHADE
EI-55
C
D
E
F
G
H
J
K
L
M
A
B
EI
Ter-
minal
Wire
color
Item
Signal
input/
output
Condition
Voltage (V)
(Approx.)
1
R/Y
Rear sunshade
front switch UP signal
Input
When rear sunshade front switch operates
5
→
0
2
W/L
Rear sunshade
front switch DOWN signal
Input
When rear sunshade front switch operates
5
→
0
3
W/B
Rear sunshade
rear switch UP signal
Input
When rear sunshade
rear switch operates
Rear control cancel switch (OFF)
5
→
0
Rear control cancel switch (ON)
5
4
R/W
Rear sunshade
rear switch DOWN signal
Input
When rear sunshade
rear switch operates
Rear control cancel switch (OFF)
5
→
0
Rear control cancel switch (ON)
5
5
P/B
Ignition switch ACC signal
Input
—
Battery voltage
6
B
Ground
—
—
0
EI-56
FLOOR TRIM
FLOOR TRIM
PFP:74902
Removal and installation
NIS0011U
REMOVAL
1.
Remove front seat and rear seat cushions. Refer to
and
.
2.
Remove center console and ashtray. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
3.
Remove front and rear kicking plate.
4.
Remove front and rear body side welt.
5.
Remove center pillar lower garnish.
6.
Remove dash side finisher.
NOTE:
For steps 3 to 6, refer to
EI-43, "Removal and Installation"
SIIA0816E
1.
Floor carpet
2.
Foot-rest
3.
Carpet hook
4.
Accelerator pedal stopper
5.
Heater nozzle (left)
6.
Heater nozzle (right)
FLOOR TRIM
EI-57
C
D
E
F
G
H
J
K
L
M
A
B
EI
7.
Turn hexagon wrench in counterclockwise, and remove acceler-
ator pedal stopper from stud bolts on vehicle.
8.
Remove heater nozzle.
9.
Cut front part of carpet, and pull to both side. Pull carpet to rear
of vehicle, and remove.
INSTALLATION
Install in the reverse order of removal.
FOOT-REST
Removal
1.
Turn up floor carpet on driver's seat.
2.
Turn hexagon wrench to counterclockwise, and remove foot-rest
from stud bolts on vehicle.
Installation
Install in the reverse order of removal.
SIIA0817E
SIIA0359E
SIIA0818E
SIIA0819E
EI-58
HEADLINING
HEADLINING
PFP:73910
Removal and Installation
NIS0011V
REMOVAL
1.
Remove rear seat cushion and seatback. Refer to
SE-191, "Removal and Installation"
.
2.
Remove body side welt (front / rear). Refer to
3.
Remove front pillar and center pillar garnish. Refer to
4.
Remove assist grip.
NOTE:
To remove assist grip of roof, insert small screw driver rolled
with waste into dip on mask, pull it back to your side, remove it
and remove screws (one each for LH/RH).
1.
Headlining
2.
Sun-visor (LH)
3.
Sun-visor (RH)
4.
Holder retainer
5.
Map lamp assembly
6.
Assist grip
7
Personal lamp
8.
Sunroof welt
9.
Cap
10.
Dual lock fastener
11.
Hook
Clip
Metal clip
PIIB7404E
SIIA0823E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст