Infiniti Q45. Manual — part 722
CHASSIS AND BODY MAINTENANCE
MA-25
C
D
E
F
G
H
I
J
K
M
A
B
MA
PAD
●
Check for wear or damage.
Unit: mm (in)
Checking Steering Gear and Linkage
NLS0004A
STEERING GEAR
●
Check gear housing and boots for looseness, damage and
grease leakage.
●
Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
Checking Power Steering Fluid and Lines
NLS0004B
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80
°
C (122 to 176
°
F)
or “COLD” range at fluid temperatures of 0 to 30
°
C (32 to 86
°
F).
CAUTION:
●
Do not overfill.
●
Recommended fluid is Genuine NISSAN PSF or equivalent.
Refer to
MA-10, "RECOMMENDED FLUIDS AND LUBRI-
SMA922A
Brake model
CLZ31VA
AD14VD
Standard thickness
10.0 (0.394)
9.8 (0.386)
Minimum thickness (Wear
limit)
2.0 (0.079)
2.0 (0.079)
BRA0010D
SLIA0014E
SST850C
MA-26
CHASSIS AND BODY MAINTENANCE
●
Check lines for improper attachment, leaks, cracks, dam-
age, loose connections, chafing and deterioration.
●
Check rack boots for accumulation of power steering fluid.
Axle and Suspension Parts
NLS0004C
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
●
Shake each wheel to check for excessive play.
●
Check wheel bearings for smooth operation.
●
Check axle and suspension nuts and bolts for looseness.
●
Check strut (shock absorber) for oil leakage or other damage.
●
Check suspension ball joint for grease leakage and ball joint
dust cover for cracks or other damage.
Lubricating Locks, Hinges and Hood Latches
NLS0004D
SST851C
SMA525A
SFA392B
PIIB1382E
CHASSIS AND BODY MAINTENANCE
MA-27
C
D
E
F
G
H
I
J
K
M
A
B
MA
Checking Seat Belt, Buckles, Retractors, Anchors and Adjusters
NLS00076
CAUTION:
●
After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in
use during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improp-
erly operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal col-
lision where the driver and passenger air bags are deployed.
●
If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
●
If webbing is cut, frayed, or damaged, replace belt assembly.
●
Never oil tongue and buckle.
●
Use a genuine NISSAN seat belt assembly.
For details, refer to
in SB section.
●
Check anchors for loose mounting
●
Check belts for damage
●
Check retractor for smooth operation
●
Check function of buckles and tongues when buckled and released
PIIB8434E
MA-28
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Standard and Limit
NLS0004F
BELT DEFLECTION AND TENSION
ENGINE COOLANT CAPACITY
Unit:
(US qt, Imp qt)
RADIATOR
Unit: kPa (kg/cm
2
, psi)
ENGINE OIL CAPACITY
Unit:
(US qt, Imp qt)
SPARK PLUG (PLATINUM-TIPPED TYPE)
WHEEL BALANCE
Unit: g (oz)
Tensions of drive belts
Auto-adjustment by auto tensioner
Engine coolant capacity [With reservoir tank (MAX level)]
Approximately 10.3 (10-7/8, 9-1/8)
Reservoir tank
0.8 (7/8, 3/4)
Cap relief pressure
Standard
78 - 98 (0.8 - 1.0, 11 - 14)
Limit
59 (0.6, 9)
Leakage test pressure
157 (1.6, 23)
With oil filter change
Approximately 5.6 (5-7/8, 4-7/8)
Without oil filter change
Approximately 5.0 (5-1/4, 4-3/8)
Dry engine (engine overhaul)
Approximately 6.7 (7-1/8, 5-7/8)
Make
NGK
Type
Standard
PLFR5A-11
Hot
PLFR4A-11
Cold
PLFR6A-11
Plug gap (Nominal)
1.1 mm (0.043 in)
Maximum allowable unbalance
Dynamic (At rim flange)
5 (0.17) (one side)
Static
10 (0.35)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст