Infiniti Q45. Manual — part 172
NAVIGATION SYSTEM
AV-117
C
D
E
F
G
H
I
J
L
M
A
B
AV
PANEL SW
[ABNORMAL CONNECTION]
Multifunction switch power supply and
ground circuit malfunction is detected
1. Check multifunction switch power supply and
ground circuit.
2. If the results from the above checkup show no mal-
function, replace multifunction switch.
●
AUDIO HEAD UNIT
[ABNORMAL CONNECTION]
●
BOSE AMP
[ABNORMAL CONNECTION]
Malfunction is detected on communication
signal between multifunction switch and
audio unit
1. Check communication circuit between multifunction
switch and audio unit.
2. If the results from the above checkup show no mal-
function, replace either multifunction switch or audio
unit, and then start self-diagnosis.
3. If self-diagnosis results still show any malfunction,
replace the other unit.
AIR COMP RECEIVER
[ABNORMAL CONNECTION]
●
Low tire pressure warning control unit
power supply and ground circuit mal-
function is detected
●
Malfunction is detected on communica-
tion signal between multifunction switch
and low tire pressure warning control
unit
1. Check low tire pressure warning control unit power
supply and ground circuit.
2. Check communication circuit between multifunction
switch and low tire pressure warning control unit.
3. If the results from the above checkup show no mal-
function, replace either multifunction switch or low
tire pressure warning control unit, and then start
self-diagnosis.
4. If self-diagnosis results still show any malfunction,
replace the other unit.
BOSE AMP
[ABNORMAL CONNECTION]
●
BOSE speaker amp. power supply and
ground circuit malfunction is detected
●
Malfunction is detected on communica-
tion signal between audio unit and BOSE
speaker amp.
1. Check BOSE speaker amp. power supply and
ground circuit.
2. Check communication circuit between audio unit
and BOSE speaker amp.
3. If the results from the above checkup show no mal-
function, replace either audio unit or BOSE speaker
amp., and then start self-diagnosis.
4. If self-diagnosis results still show any malfunction,
replace the other unit.
AUDIO HEAD UNIT
[ABNORMAL CONNECTION]
Audio unit power supply and ground circuit
malfunction is detected
1. Check audio unit power supply circuit.
2. If the results from the above checkup show no mal-
function, replace audio unit.
Error item
Possible cause
Action to take
AV-118
NAVIGATION SYSTEM
CD CHANGER
[ABNORMAL CONNECTION]
Without satellite radio
●
CD auto changer power supply and
ground circuit malfunction is detected
●
Malfunction is detected on communica-
tion signal [REQ (CHG-AUDIO), Tx and
RX] between audio unit and CD auto
changer
1. Check CD auto changer power supply and ground
circuit.
2. Check communication circuit [REQ (CHG-AUDIO),
Tx and RX] between audio unit and CD auto
changer.
3. Check communication signal [REQ (CHG-AUDIO),
Tx and RX] between audio unit and CD auto
changer.
4. If the results from the above checkup show no mal-
function, replace either audio unit or CD auto
changer, and then start self-diagnosis.
5. If self-diagnosis results still show any malfunction,
replace the other unit.
With satellite radio
●
CD auto changer power supply and
ground circuit malfunction is detected
●
Satellite radio tuner power supply and
ground circuit malfunction is detected
●
Malfunction is detected on communica-
tion signal [REQ (CHG-AUDIO), REQ
(SAT-AUDIO), Tx and RX] between
audio unit and satellite radio tuner
●
Malfunction is detected on control signal
(CONT) between audio unit and satellite
radio tuner
●
Malfunction is detected on communica-
tion signal [REQ (CHG-AUDIO), Tx and
Rx] between satellite radio tuner and CD
auto changer
1. Check CD auto changer power supply and ground
circuit.
2. Check satellite radio tuner power supply and ground
circuit.
3. Check communication circuit [REQ (CHG-AUDIO),
REQ (SAT-AUDIO), Tx and RX] between audio unit
and satellite radio tuner.
4. Check control signal circuit (CONT) between audio
unit and satellite radio tuner.
5. Check communication circuit [REQ (CHG-AUDIO),
Tx and Rx] between satellite radio tuner and CD
auto changer.
6. Check communication signal [REQ (CHG-AUDIO),
REQ (SAT-AUDIO), Tx and RX] between audio unit
and satellite radio tuner.
7. Check control signal (CONT) between audio unit
and satellite radio tuner.
8. Check communication signal [REQ (CHG-AUDIO),
Tx and Rx] between satellite radio tuner and CD
auto changer.
9. If the results from the above checkup show no mal-
function, replace audio unit, satellite radio tuner, or
CD auto changer, and then start self-diagnosis.
10.If self-diagnosis results still show any malfunction,
replace one of the two units that is not replaced yet.
11.If self-diagnosis results still show any malfunction,
replace the other unit.
FRONT SEAT DISPLAY
[ABNORMAL CONNECTION]
Display power supply and ground circuit
malfunction is detected
1. Check display power supply and ground circuit.
2. If the results from the above checkup show no mal-
function, replace display.
VOICE UNIT
[ABNORMAL CONNECTION]
●
Voice activated control module power
supply and ground circuit malfunction is
detected
●
Malfunction is detected on communica-
tion signal between AV and NAVI control
unit and voice activated control module
1. Check voice activated control module power supply
and ground circuit.
2. Check communication circuit between AV and NAVI
control unit and voice activated control module.
3. If the results from the above checkup show no mal-
function, replace either AV and NAVI control unit or
voice activated control module, and then start self-
diagnosis.
4. If self-diagnosis results still show any malfunction,
replace the other unit.
Error item
Possible cause
Action to take
NAVIGATION SYSTEM
AV-119
C
D
E
F
G
H
I
J
L
M
A
B
AV
SIGNAL MONITOR
●
When “SIGNAL MONITOR” is selected, “ALL SIGNALS” and
“SELECTION FROM MENU” are displayed.
●
For each signal, a comparison of actual operating status and the
status recognized by the system can be checked.
Display Condition
SKIB0653E
Diagnosis item
Display
Condition
Remarks
VHCL SPD SIG
ON
When vehicle speed is more than 0 km/h (0 MPH)
Changes in indication may be delayed.
This is normal.
OFF
When vehicle speed is 0 km/h (0 MPH)
—
Ignition switch in ACC position
MTR ILL DIM
ON
Lighting switch is ON, and then optical sensor is
not illuminated
—
OFF
Lighting switch OFF
Lighting switch is ON, and then optical sensor is
illuminated
IGN SW
ON
Ignition switch ON
—
OFF
Ignition switch ACC position
AV-120
NAVIGATION SYSTEM
RGB Image Is Not Displayed (Rear View Image Is Displayed)
NKS001J6
Symptom: RGB image such as a map screen is not displayed. (No warning message though rear view image
is displayed.)
1.
CHECK HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect AV and NAVI control unit and display connectors.
3.
Check continuity between AV and NAVI control unit harness
connector (A) B30 terminal 12 and display harness connector
(B) M82 terminal 8.
4.
Check continuity between AV and NAVI control unit harness
connector (A) B30 terminal 12 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair harness or connector.
2.
CHECK RGB AREA (YS) SIGNAL
1.
Turn ignition switch OFF.
2.
Connect AV and NAVI control unit and display connectors.
3.
Check voltage waveform between AV and NAVI control unit har-
ness connector B30 terminal 12 and ground with CONSULT-ll or
oscilloscope.
OK or NG
OK
>> Replace display.
NG
>> Replace AV and NAVI control unit.
12 – 8
: Continuity should exist.
12 – Ground
: Continuity should not exist.
SKIB7650E
12 – Ground:
When displaying rear view image
When displaying RGB image
SKIB7651E
SKIB3599E
SKIB3600E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст