Infiniti Q45. Manual — part 538
ROOF SIDE MOLDING
EI-31
C
D
E
F
G
H
J
K
L
M
A
B
EI
ROOF SIDE MOLDING
PFP:73854
Removal and Installation
NIS0011I
REMOVAL
1.
Lift and twist roof side molding up from rear edge.
2.
Disengage clips, and remove roof side molding.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
To install roof side molding, always insert its front edge part inside of windshield molding.
●
Be careful not to damage the body.
PIIA0040E
EI-32
DOOR OUTSIDE MOLDING
DOOR OUTSIDE MOLDING
PFP:82820
Removal and Installation
NIS0011J
FRONT DOOR OUTSIDE MOLDING
Removal
1.
Open windows fully.
2.
Lift up rear edge, push down center tip of clip, and pull out molding.
3.
Lift and twist from rear side, disengage clips from flange, and pull out molding to backward.
Installation
Install in the reverse order of removal.
CAUTION:
●
Be careful not to apply excessive force when removing because it is easy to deform parts.
●
After removal, visually inspect molding, and if it is deformed, replace it with new molding.
REAR DOOR OUTSIDE MOLDING
Removal
1.
Open windows fully.
2.
Remove screws on rear edge.
3.
Lift and twist from rear side, and disengage clips from flange.
4.
Push down center tip of clip, pull out and remove molding.
Installation
Install in the reverse order of removal.
CAUTION:
●
Be careful not to apply excessive force when removing because it is easy to deform parts.
●
After removal, visually inspect molding, and if it is deformed, replace it with new molding.
PIIA0042E
SIDE GUARD MOLDING
EI-33
C
D
E
F
G
H
J
K
L
M
A
B
EI
SIDE GUARD MOLDING
PFP:76840
Removal and Installation
NIS0011K
REMOVAL
1.
Apply masking tape around outer circumference of side guard molding.
2.
Remove double-faced adhesive tapes with (wide) resin spatula. Disengage clips and remove side guard
molding (front/center/rear).
INSTALLATION
1.
Remove double-faced adhesive tape remaining on vehicle.
2.
Clean contact surface of vehicle (to side guard molding), and install side guard molding to vehicle.
●
To re-use side guard molding, follow above steps 1 and 2 as well; clean surface after removing double-
faced adhesive tape, apply new double-faced adhesive tape as shown in illustration, then install side
guard molding to vehicle.
CAUTION:
●
Do not let air between contact surfaces when installing.
●
To secure contact, do not wash vehicle within 24 hours after installation.
PIIB1695E
1.
Side guard molding (front)
2.
Side guard molding (center)
3.
Side guard molding (rear)
Double–faced adhesive tape
thickness: 6 mm (0.24 in) (upper
side)
thickness: 8 mm (0.31 in) (lower
side)
EI-34
TRUNK LID FINISHER
TRUNK LID FINISHER
PFP:84810
Removal and Installation
NIS0011L
TRUNK LID FINISHER AND TRUNK LID FINISHER LOWER
Removal
1.
Open trunk lid fully.
2.
Remove trunk lid finisher (inner). Refer to
EI-60, "TRUNK ROOM TRIM & TRUNK LID FINISHER"
3.
Remove trunk close switch assembly bolts.
4.
Remove nuts of trunk lid finisher lower.
5.
Remove nuts of trunk lid finisher.
6.
Disengage clips, and remove trunk lid finisher, trunk lid finisher
lower.
Installation
Install in the reverse order of removal.
CAUTION:
Note that trunk lid might be distorted when nuts is tightened too much.
1.
Nut
2.
Stud bolt
3.
Clip (C101)
4.
Trunk lid finisher lower
5.
Trunk lid finisher
6.
Emblem
7.
BI mark
8.
Back view camera
PIIB1696E
PIIB1703E
: 1.3 - 1.7 N·m (0.14 - 0.17 Kg-m, 12 - 15 in-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст