Infiniti Q45. Manual — part 539
DOOR FINISHER
EI-35
C
D
E
F
G
H
J
K
L
M
A
B
EI
DOOR FINISHER
PFP:80900
Removal and Installation
NIS0011M
1.
Front door sash cover
2.
Inside handle escutcheon (front)
3.
Front door finisher
4.
Front armrest finisher
5.
Front door upper finisher
6.
Rear door sash cover
7.
Hook
8.
Rear side sunshade
9.
Inside handle escutcheon (rear)
10.
Rear door finisher
11.
Rear armrest finisher
12.
Rear door lower finisher
13.
Bumper rubber
14.
Step lamp
SIIA0805E
EI-36
DOOR FINISHER
FRONT DOOR FINISHER
Removal
1.
Insert screwdriver rolled with cloth or tapes into dip at rear of
inside handle escutcheon, and pull it back to your side. Discon-
nect upper pawl, lower and front, and remove inside handle
escutcheon.
2.
Insert clip screwdriver rolled with cloth into dip under arm-rest
finisher, and lift up finisher. Insert your fingers between gaps,
pull it back to your side and disconnect metal clips.
3.
Disconnect trunk lid opener and fuel lid opener switch connec-
tor.
4.
Insert screwdriver rolled with cloth under front part of front door
upper finisher, pull it back to your side and remove it.
5.
Disconnect door control unit connector under arm-rest.
6.
Remove step lamp, and disconnect connectors.
7.
Remove nine screws of door finisher.
8.
Insert screwdriver rolled with cloth into clips under door finisher, and disconnect clips.
9.
Pull up door finisher, and remove connectors, inside handle
cable and lock knob cable.
10. Remove front door finisher clips, and remove front door finisher.
SIIA0806E
SIIA0807E
SIIA0808E
SIIA0266E
DOOR FINISHER
EI-37
C
D
E
F
G
H
J
K
L
M
A
B
EI
NOTE:
Insert screwdriver rolled with cloth between panel on vehicle and
clips (as indicated with arrow).
Installation
Install in the reverse order of removal.
CAUTION:
To install finisher, check if all clips are matched over holes of panel on vehicle, then push in.
REAR DOOR FINISHER
Removal
1.
Insert screwdriver rolled with cloth or tape into dip at rear of
inside handle escutcheon, and pull it back to your side. Disen-
gage upper pawls, lower and front, and remove inside handle
escutcheon.
2.
Insert screwdriver rolled with cloth into dip under arm-rest fin-
isher, and lift up finisher. Insert your fingers between gaps, pull it
back to your side, and disconnect metal clips.
3.
Insert screwdriver rolled with cloth under rear door lower fin-
isher, and pull it back to your side. Remove rear door lower fin-
isher and disconnect connectors.
4.
Disconnect door control unit connector under arm-rest.
5.
Remove step lamp, and disconnect connectors.
6.
Remove seven screws of door finisher.
SIIA0810E
SIIA0806E
SIIA0807E
SIIA0809E
EI-38
DOOR FINISHER
7.
Insert screwdriver rolled with was cloth into clips of door finisher, and disconnect clips.
8.
Pull up door finisher, and remove connectors, inside handle
cable and lock knob cable.
9.
Remove rear door finisher clips, and remove rear door finisher.
NOTE:
Insert screwdriver rolled with cloth between panel on vehicle and
clips (as indicated with arrow).
Installation
Install in the reverse order of removal.
CAUTION:
To install finisher, check if all clips are matched over holes of panel on vehicle, then push in.
FRONT DOOR SASH COVER
Removal
1.
Remove front door finisher.
2.
Remove screws, and remove from door sash cover.
Installation
Install in the reverse order of removal.
REAR DOOR SUSH COVER
Removal
1.
Remove rear door finisher.
2.
Remove screw, and remove rear side sunshade.
SIIA0266E
SIIA0810E
PIIA9283E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст