Infiniti G37 Coupe. Manual — part 414
FRONT FENDER
DLK-217
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT FENDER
Exploded View
INFOID:0000000001722594
Removal and Installation
INFOID:0000000001722595
REMOVAL
1.
Remove the front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
2.
Remove the hood seal assembly (side).
3.
Remove the front combination lamp. Refer to
EXL-189, "Removal and Installation"
.
4.
Remove the fender protector. Refer to
EXT-24, "FENDER PROTECTOR : Removal and Installation"
.
5.
Remove the center mudguard. Refer to
EXT-27, "Removal and Installation"
6.
Remove the mounting bolt and remove the front fender.
CAUTION:
While removing use a shop cloth to protect body from damaging.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installing, apply touch-up paint (the body color) onto the head of the front fender mounting
bolts.
• After installing, check front fender adjustment. Refer to
DLK-210, "HOOD ASSEMBLY : Adjustment"
DLK-219, "DOOR ASSEMBLY : Adjustment"
.
1.
Hood seal assembly (side)
2.
Front fender
3.
Baffle assembly
4.
Double-faced adhesive tape
JMKIA1215ZZ
DLK-218
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
DOOR
DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Exploded View
INFOID:0000000001722596
REMOVAL
ADJUSTMENT
1.
Door panel
2.
Door striker
3.
TORX bolt
4.
Door striker cover
5.
Check link
6.
Door hinge (upper, lower)
Refer to
for symbols in the figure.
JMKIA1216ZZ
DOOR
DLK-219
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000001722597
REMOVAL
CAUTION:
• When removing and installing the door assembly, support the door with a jack and cloth to protect
the door and body.
• When removing and installing door assembly, perform the fitting adjustment. Refer to
.
• After installing, apply touch-up paint (the body color) onto the head of the hinge mounting nuts.
• Check the hinge rotating part for poor lubrication. If necessary, apply body grease.
• Operate with two workers, because of its heavy weight.
• Check door open/close operation after installation.
1.
Remove the mounting bolts of the check link on the vehicle.
2.
Pull the lever and disconnect the door harness connector while removing tabs of door harness connector.
3.
Remove the door side hinge mounting nuts, then remove the door assembly.
INSTALLATION
Install in the reverse order of removal.
DOOR ASSEMBLY : Adjustment
INFOID:0000000001722598
CLEARANCE, SURFACE HEIGHT AND SURFACE MISMATCH ADJUSTMENT
1.
Check the clearance and surface height and surface mismatch between the door and each part visually
and by touching. (Fitting standard dimension in the table below should be satisfied.)
1.
Front fender
2.
Door panel
3.
Rear fender
4.
Door hinge
5.
Door striker
Refer to
JMKIA1217GB
DLK-220
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
DOOR
2.
In case out of specification, adjust them according to the procedures shown below.
3.
Remove the front fender. Refer to
DLK-217, "Removal and Installation"
4.
Loosen the hinge mounting nuts on door side.
5.
Adjust the surface height and surface mismatch of the door according to the fitting standard dimension.
6.
Temporarily tighten the hinge mounting nuts on door side.
7.
Loosen the hinge mounting bolts on body side.
8.
Raise the door at rear end to adjust clearance of the front according to the fitting standard dimension.
9.
After adjustment tighten bolts and nuts to the specified torque.
10. Install the front fender. Refer to
DLK-217, "Removal and Installation"
.
STRIKER ADJUSTMENT
Adjust the striker so that it becomes parallel with the lock insertion
direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000001722619
Portion
Clearance
Surface height
Front fender – Door
A – A
2.5 – 4.5 mm
(0.098 – 0.177 in)
−
1.0 – 1.0 mm
(
−
0.039 – 0.039 in)
Door – Rear fender
B – B
2.5 – 4.5 mm
(0.098 – 0.177 in)
−
1.0 – 1.0 mm
(
−
0.039 – 0.039 in)
PIIB2804J
1.
Door panel
2.
Door striker
3.
TORX bolt
4.
Door striker cover
5.
Check link
6.
Door hinge (upper, lower)
Refer to
for symbols in the figure.
JMKIA1216ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст