Infiniti G37 Coupe. Manual — part 415
DOOR
DLK-221
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR STRIKER : Removal and Installation
INFOID:0000000001722620
REMOVAL
1.
Remove the door striker cover.
2.
Remove the TORX bolts, and then remove the door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check the door open/close operation after installation.
• When removing and installing the door striker, be sure to perform the fitting adjustment. Refer to
DLK-219, "DOOR ASSEMBLY : Adjustment"
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000001736637
DOOR HINGE : Removal and Installation
INFOID:0000000001722600
REMOVAL
1.
Remove the door assembly. Refer to
DLK-219, "DOOR ASSEMBLY : Removal and Installation"
.
2.
Remove the door hinge mounting bolts, and then remove the door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• When removing and installing the door assembly, perform the fitting adjustment. Refer to
.
• After installation, apply touch-up paint (the body color) onto the head of the door hinge mounting
nuts.
• Check the door hinge rotating part for poor lubrication. If necessary, apply body grease.
• Check the door open/close operation after installation.
DOOR CHECK LINK
1.
Door panel
2.
Door striker
3.
TORX bolt
4.
Door striker cover
5.
Check link
6.
Door hinge (upper, lower)
Refer to
JMKIA1216ZZ
DLK-222
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
DOOR
DOOR CHECK LINK : Exploded View
INFOID:0000000001736638
DOOR CHECK LINK : Removal and Installation
INFOID:0000000001722602
REMOVAL
1.
Remove the door finisher. Refer to
INT-11, "Removal and Installation"
.
2.
Remove the door speaker.
3.
Remove the mounting bolt of the door check link on the vehicle.
4.
Remove the door check link mounting bolts on the door side.
5.
Remove the door check link.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check the door open/close operation after installation.
1.
Door panel
2.
Door striker
3.
TORX bolt
4.
Door striker cover
5.
Check link
6.
Door hinge (upper, lower)
Refer to
for symbols in the figure.
JMKIA1216ZZ
TRUNK LID
DLK-223
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID
TRUNK LID ASSEMBLY
TRUNK LID ASSEMBLY : Exploded View
INFOID:0000000001722610
REMOVAL
ADJUSTMENT
1.
Trunk lid assembly
2.
Trunk lid hinge stopper
3.
Trunk lid hinge
4.
Trunk lid stay
5.
Trunk lid striker
6.
Trunk lid lock cover
7.
Trunk lid lock assembly
8.
Trunk lid opener cable
9.
Trunk lid emergency opener lever
holder
10. Trunk lid emergency opener lever
11.
Bumper rubber
Refer to
for the symbols in the figure.
JMKIA1218GB
DLK-224
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID ASSEMBLY : Removal and Installation
INFOID:0000000001722611
REMOVAL
1.
Remove the trunk lid finisher inner. Refer to
INT-29, "Removal and Installation"
.
2.
Disconnect the connectors in the trunk lid, and remove the harness clamps to pull the harness out of the
trunk lid.
3.
Remove trunk lid stay at trunk lid side.
NOTE:
Insert flat-bladed screwdriver into the gap and remove holder.
WARNING:
Body injury may occur if no supporting rod is holding the trunk lid open when removing the stay.
CAUTION:
While removing use a shop cloth or tape to protect from damaging.
4.
Remove the trunk lid hinge mounting bolts on trunk lid side and remove the trunk lid assembly.
INSTALLATION
1.
Trunk lid assembly
2.
Bumper rubber
3.
Trunk lid hinge
4.
Trunk lid striker
5.
Rear fender
6.
Rear combination lamp
7.
Rear bumper
Refer to
for symbols in the figure.
JMKIA1219GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст