Infiniti G37 Coupe. Manual — part 820
DOOR FINISHER
INT-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
ON-VEHICLE REPAIR
DOOR FINISHER
Exploded View
INFOID:0000000001722841
Removal and Installation
INFOID:0000000001722842
REMOVAL
1.
Fully open door window.
1.
Door panel assembly
2.
Inside handle escutcheon
3.
Power window switch finisher
4.
Door finisher assembly
5.
Armrest cap
6.
Step lamp
7.
Speaker grille
8.
Seat memory switch
9.
Mirror control switch
10. Power window switch
: Clip
: Pawl
: Metal clip
JMJIA0956ZZ
INT-12
< ON-VEHICLE REPAIR >
DOOR FINISHER
2.
Remove inside handle escutcheon (1) with remover tool (A).
3.
Remove screw (A), located on the back side of inside handle
escutcheon.
4.
Remove armrest cap (1) with remover tool (A).
5.
Remove screws (A), located on the back side of power window
finisher.
6.
Remove step lamp (1).
Refer to
INL-101, "Removal and Installation"
: Pawl
JMJIA0073GB
JMJIA0074GB
: Pawl
JMJIA0957ZZ
JMJIA0958ZZ
JMJIA0077GB
DOOR FINISHER
INT-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
7.
Insert a remover tool (A) into clips on door finisher (1), and dis-
engage clips.
CAUTION:
Insert a remover tool (A) into the part shown by the arrow
(between the clips and the body side panel).
8.
Pull up door finisher and pull out toward vehicle inside.
• Disconnect seat memory switch connector (A) (with ADP).
• Disconnect tweeter connector (B) (with BASE AUDIO).
• Disconnect door squawker connector (B) (with BOSE AUDIO).
9.
Disconnect lock knob cable (1) and inside handle cable (2) from
door inside handle assembly.
10. Disconnect power window switch connector and mirror control switch connector.
11. Remove door finisher.
12. Remove the following parts after removing door finisher.
• Door inside handle assembly. Refer to
DLK-233, "INSIDE HANDLE : Removal and Installation"
.
• Seat memory switch (with ADP). Refer to
ADP-238, "Removal and Installation"
• Tweeter (with BASE AUDIO). Refer to
AV-113, "Removal and Installation"
.
• Door squawker (with BOSE AUDIO). Refer to
AV-610, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
: Clip
JMJIA0078GB
JMJIA0080GB
JMJIA0079GB
INT-14
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
BODY SIDE TRIM
Exploded View
INFOID:0000000001722843
Removal and Installation
INFOID:0000000001722844
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
• Do not damage the body.
REMOVAL
FRONT PILLAR GARNISH
1.
Release front pillar portion of body side welt.
1.
Front pillar garnish
2.
Kicking plate outer
3.
Dash side finisher
4.
Kicking plate inner
5.
Rear side finisher
6.
Rear pillar finisher
7.
Back pillar garnish
8.
Body side welt
: Clip
: Pawl
: Metal clip
JMJIA0959ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст