Infiniti G37 Coupe. Manual — part 821
BODY SIDE TRIM
INT-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Remove front pillar garnish fixing clip and metal clip with a
remover tool (A), and then remove front pillar garnish (1).
DASH SIDE FINISHER
1.
Remove instrument passenger lower cover. Refer to
IP-12, "Removal and Installation"
.
2.
Remove kicking plate inner.
3.
Remove clip (A).
4.
Remove dash side finisher fixing clips with a remover tool (B),
and then remove dash side finisher (1).
KICKING PLATE OUTER
Remove kicking plate outer fixing clips with a remover tool (A), and
then remove kicking plate outer (1).
KICKING PLATE INNER
1.
Pull up kicking plate inner, and disconnect pawls.
2.
Remove kicking plate inner (1).
BODY SIDE WELT
1.
Remove kicking plate inner.
2.
Remove body side welt.
REAR SIDE FINISHER
1.
Remove rear seat cushion and rear seatback. Refer to
SE-160, "Removal and Installation"
.
: Clip
: Metal clip
JMJIA0960ZZ
: Clip
JMJIA0961ZZ
: Clip
JMJIA0082GB
: Pawl
JMJIA0962ZZ
INT-16
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
2.
Remove body side welt.
3.
Remove rear side finisher (1) fixing clips with a remover tool (A),
and then disconnect rear speaker harness connector.
4.
Remove rear side finisher.
BACK PILLAR GARNISH
1.
Remove back pillar garnish (1) fixing clips and pawls with a
remover tool (A).
2.
Remove back pillar garnish (1) from rear pillar finisher (2).
REAR PILLAR FINISHER
1.
Remove rear seat cushion and rear seatback. Refer to
SE-160, "Removal and Installation"
.
2.
Remove body side welt.
3.
Remove rear side finisher.
4.
Remove front seat belt floor anchor bolt. Refer to
SB-5, "SEAT BELT RETRACTOR : Exploded View"
.
5.
Remove rear seat belt floor anchor bolt. Refer to
SB-10, "SEAT BELT RETRACTOR : Exploded View"
6.
Remove rear seat belt escutcheon fixing pawls with remover tool
(A), and then remove rear seat belt escutcheon (1) from rear pil-
lar finisher (2).
7.
Remove back pillar garnish.
8.
Remove rear pillar finisher fixing clips, pawl, metal clips with a remover tool, and then remove rear pillar
finisher.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check that clips are securely fitted in panel holes on body when installing, and then press them in.
: Clip
JMJIA0963ZZ
: Clip
: Pawl
JMJIA0964ZZ
: Pawl
JMJIA0965ZZ
REAR PARCEL SHELF FINISHER
INT-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
REAR PARCEL SHELF FINISHER
Exploded View
INFOID:0000000001722845
Refer to
for symbols in the figure.
Removal and Installation
INFOID:0000000001722846
REMOVAL
1.
Remove trunk front finisher upper (without REAR SPOILER). Refer to
INT-27, "Removal and Installation"
.
1.
Rear speaker grille
2.
Child anchor cover
3.
Rear seatback finisher RH
4.
Rear seatback finisher LH
5.
Push on nut
6.
Rear parcel shelf finisher
7.
Rear seatback welt
8.
High-mounted stop lamp assembly
9.
High-mounted stop lamp cover
10. Rear seat striker cover
: Clip
: Pawl
JMJIA0966ZZ
INT-18
< ON-VEHICLE REPAIR >
REAR PARCEL SHELF FINISHER
2.
Disconnect high-mounted stop lamp harness connector (A).
(without REAR SPOILER)
3.
Remove rear seat cushion and rear seatback. Refer to
SE-160, "Removal and Installation"
.
4.
Remove rear side finisher and rear pillar finisher. Refer to
INT-14, "Removal and Installation"
5.
Remove rear parcel shelf finisher mounting clips (A).
6.
Remove rear seat striker cover fixing pawls, and then remove rear seat striker cover.
7.
Pull rear parcel shelf finisher, and then remove rear parcel shelf finisher.
8.
Remove the following parts after removing rear parcel shelf finisher.
• Child anchor cover.
• Rear speaker grille.
• High-mounted stop lamp (without REAR SPOILER). Refer to
EXL-202, "WITHOUT REAR SPOILER :
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check that clips are securely fitted in panel holes on body when installing, and then press them in.
JMJIA0090GB
JMJIA0967ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст