Infiniti G37 Coupe. Manual — part 1185
SPIRAL CABLE
SR-9
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SR-10
< ON-VEHICLE REPAIR >
FRONT PASSENGER AIR BAG MODULE
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000001694457
Removal and Installation
INFOID:0000000001694458
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Always work from the side of air bag module. Do not work in front of it.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove the glove box assembly. Refer to
IP-12, "Removal and Installation"
2.
Remove the Instrument lower assist panel. Refer to
IP-12, "Removal and Installation"
.
3.
Disconnect passenger air bag module harness connector (A)
from passenger air bag module (1).
4.
Remove the passenger air bag module fixing bolt and screws.
NOTE:
The figure shows the installed front passenger air bag module. (Under view of the module installed without
glove box cover.)
JMHIA0134GB
1.
Passenger air bag modulel
2.
Instrument panel assembly
Refer to
for symbols in the figure.
JMHIA0014ZZ
FRONT PASSENGER AIR BAG MODULE
SR-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
5.
Disconnect pawls (A)(B), and then remove passenger air bag
module.
CAUTION:
• Always place passenger air bag module with pad side facing
upward.
• Do not insert any foreign objects (screwdriver, etc.) into pas-
senger air bag module.
• Do not disassemble passenger air bag module.
• Do not use old fixing bolts after removal; replace with new
bolts.
• Do not expose the passenger air bag module to temperatures
exceeding 90
°
C (194
°
F).
• Do not allow oil, grease or water to come in contact with the
passenger air bag module.
• Replace the passenger air bag module if it has been dropped
or sustained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Do not damage the harness while installing.
• In the case that a malfunction is detected by the air bag warning lamp, reset by the self-diagnosis
function and delete the memory by CONSULT-III.
• In the case that a malfunction is still detected after the above operation, peform self-diagnosis to
repair malfunctions.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SRC-15, "Diagnosis Description"
: Vehicle front
JMHIA0016ZZ
: Upward
JMHIA0017ZZ
JMHIA0009ZZ
SR-12
< ON-VEHICLE REPAIR >
SIDE CURTAIN AIR BAG MODULE
SIDE CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000001694459
Removal and Installation
INFOID:0000000001694460
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove the headlining. Refer to
INT-21, "NORMAL ROOF : Removal and Installation"
ROOF : Removal and Installation"
2.
Remove the side curtain air bag module harness connector.
NOTE:
• For installing/removing side curtain air bag module harness
connector, insert thin screwdriver wrapped in tape into notch,
lift lock and remove connector.
• Install connector with lock raised, and push lock into connec-
tor.
• After installing the connector, check that the lock is pushed
securely into it.
3.
Remove fixing bolts, and then remove side curtain air bag module.
CAUTION:
• Do not insert any foreign objects (screwdriver, etc.) into side curtain air bag module.
• Do not disassemble side curtain air bag module.
• Do not expose the side curtain air bag module to temperatures exceeding 90
°
C (194
°
F).
• Do not allow oil, grease or water to come in contact with the side curtain air bag module.
JMHIA0425GB
1.
Side curtain air bag
2.
Side curtain air bag inflator
A.
Side curtain air bag module harness
connector
Refer to
for symbols in the figure.
PHIA0953J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст