Infiniti G37 Coupe. Manual — part 1186
SIDE CURTAIN AIR BAG MODULE
SR-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Replace the side curtain air bag module if it has been dropped
or sustained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Do not damage the harness while installing.
• In the case that a malfunction is detected by the air bag warning lamp, reset by the self-diagnosis
function and delete the memory by CONSULT-III.
• In the case that a malfunction is still detected after the above operation, perform self-diagnosis to
repair malfunctions.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SRC-15, "Diagnosis Description"
JMHIA0009ZZ
SR-14
< ON-VEHICLE REPAIR >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Exploded View
INFOID:0000000001694461
Removal and Installation
INFOID:0000000001694462
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove the reservoir tank. Refer to
2.
Remove the crash zone sensor fixing nuts.
3.
Disconnect crash zone sensor harness connector.
CAUTION:
• Do not use old fixing nuts after removal; replace with new nuts.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
• Replace the crash zone sensor of deployed SRS driver air bag
and deployed SRS front passenger air bag.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Do not damage the harness while installing.
• In the case that a malfunction is detected by the air bag warning lamp, reset by the self-diagnosis
function and delete the memory by CONSULT-III.
• In the case that a malfunction is still detected after the above operation, perform self-diagnosis to
repair malfunctions.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SRC-15, "Diagnosis Description"
JMHIA0019GB
1.
Crash zone sensor
A.
Crash zone sensor harness connec-
tor
Refer to
for symbols in the figure.
JMHIA0009ZZ
SIDE AIR BAG (SATELLITE) SENSOR
SR-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE AIR BAG (SATELLITE) SENSOR
Exploded View
INFOID:0000000001694463
Removal and Installation
INFOID:0000000001694464
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove the front seat belt. Refer to
SB-5, "SEAT BELT RETRACTOR : Removal and Installation"
2.
Remove the satellite sensor fixing nuts.
3.
Disconnect harness connector and then remove satellite sensor.
CAUTION:
• Do not use old fixing nuts after removal; replace with new nuts.
• Replace the satellite sensor if it has been dropped or sus-
tained an impact.
• Replace the satellite sensor of deployed SRS front side air
bag module and deployed SRS side curtain air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Do not damage the harness while installing.
• In the case that a malfunction is detected by the air bag warning lamp, reset by the self-diagnosis
function and delete the memory by CONSULT-III.
• In the case that a malfunction is still detected after the above operation, perform self-diagnosis to
repair malfunctions.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SRC-15, "Diagnosis Description"
JMHIA0020GB
1.
Satellite sensor
A.
Satellite sensor harness connector
Refer to
for symbols in the figure.
JMHIA0009ZZ
SR-16
< ON-VEHICLE REPAIR >
DIAGNOSIS SENSOR UNIT
DIAGNOSIS SENSOR UNIT
Exploded View
INFOID:0000000001694465
Removal and Installation
INFOID:0000000001694466
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each har-
ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by
static electricity and pre-tensioner seat belt operation.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Disconnect each connector of all air bag modules and pre-tensioner seat belts.
2.
Remove the center console assembly. Refer to
IP-24, "Removal and Installation"
3.
Remove the center console rear bracket. Refer to
.
4.
Disconnect diagnosis sensor unit harness connector.
5.
Remove TORX bolts, ground bolt, and then remove diagnosis sensor unit.
CAUTION:
• Do not use old TORX bolts after removal; replace with new TORX bolts.
• Replace the diagnosis sensor unit if it has been dropped or
sustained an impact.
• Replace the diagnosis sensor unit of deployed SRS air bag
and deployed SRS front seat belt pre-tensioner.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
JMHIA0369GB
1.
Diagnosis sensor unit
2.
TORX bolt
A.
Diagnosis sensor unit harness con-
nectors
Refer to
for symbols in the figure.
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст