Infiniti G37 Coupe. Manual — part 418
DOOR LOCK
DLK-233
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSIDE HANDLE : Exploded View
INFOID:0000000001736723
INSIDE HANDLE : Removal and Installation
INFOID:0000000001722622
REMOVAL
1.
Remove the door finisher. Refer to
INT-11, "Removal and Installation"
2.
Remove the inside handle mounting bolts.
3.
Disconnect the inside handle cable, and then remove the inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check the door lock/unlock operation after installation.
• Check the door open/close operation after installation.
OUTSIDE HANDLE
1.
Rear gasket
2.
TORX bolt
3.
Key cylinder rod (Driver side only)
4.
Door lock assembly
5.
Inside handle cap
6.
Inside handle
7.
Inside handle bracket
8.
Outside handle
9.
Door key cylinder assembly (Driver
side)
Outside handle escutcheon (Pas-
senger side)
10. Outside handle bracket
11.
Front gasket
Refer to
JMKIA1220GB
DLK-234
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
DOOR LOCK
OUTSIDE HANDLE : Exploded View
INFOID:0000000001736724
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000001722624
REMOVAL
1.
Remove the door finisher. Refer to
INT-11, "Removal and Installation"
.
2.
Remove the door glass and door module assembly.
• Door glass: Refer to
GW-16, "Removal and Installation"
• Door module: Refer to
GW-19, "Removal and Installation"
3.
Remove the door side grommet, and loosen door key cylinder assembly (driver side) and outside handle
escutcheon (passenger side) TORX bolt from grommet hole.
CAUTION:
1.
Rear gasket
2.
TORX bolt
3.
Key cylinder rod (Driver side only)
4.
Door lock assembly
5.
Inside handle cap
6.
Inside handle
7.
Inside handle bracket
8.
Outside handle
9.
Door key cylinder assembly (Driver
side)
Outside handle escutcheon (Pas-
senger side)
10. Outside handle bracket
11.
Front gasket
Refer to
for symbols in the figure.
JMKIA1220GB
DOOR LOCK
DLK-235
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Do not forcibly remove the TORX bolt.
4.
Disconnect the door antenna and door request switch connector and remove the harness clamp.
5.
Reach in to separate the key cylinder rod connection (on the handle).
6.
While pulling the outside handle, remove the door key cylinder
assembly.
7.
Slide toward rear of vehicle, and pull forward to remove the out-
side handle.
8.
Remove the front gasket and rear gasket.
JMKIA0020ZZ
PIIB5809E
JMKIA0967ZZ
PIIB5811E
DLK-236
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
DOOR LOCK
9.
Remove the TORX bolt of the outside handle bracket.
10. While pulling the outside handle bracket, slide toward rear of
vehicle to remove the outside handle bracket.
11. Reach in to separate the outside handle cable connection.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
To install each rod, rotate the rod holder until a click is felt.
JMKIA0022ZZ
PIIB5814E
PIIB5815E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст