Infiniti G37 Coupe. Manual — part 416
TRUNK LID
DLK-225
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Install in the reverse order of removal.
CAUTION:
• After installing, apply touch-up paint (the body color) onto the head of the hinge mounting bolts.
• After installing, check operation.
• After installing, perform fitting adjustment. Refer to
DLK-225, "TRUNK LID ASSEMBLY : Adjust-
TRUNK LID ASSEMBLY : Adjustment
INFOID:0000000001722612
1.
Check the clearance and the evenness between the trunk lid and each part visually and by touching. (Fit-
ting standard dimension in the table below should be satisfied.)
2.
In case out of specification, adjust them according to the procedures shown below.
3.
Loosen the bumper rubber.
4.
Loosen the striker mounting bolts.
5.
Lift up the trunk lid approximately 100 – 150 mm (3.937 – 5.906 in) height then close it lightly and check
that it is engaged firmly with the trunk lid closed.
6.
Check the clearance and evenness.
7.
Finally tighten the trunk lid striker.
TRUNK LID STRIKER
TRUNK LID STRIKER : Exploded View
INFOID:0000000001831344
REMOVAL
Portion
Standard
Right/left
Clearance (MAX)
Trunk lid –
Rear fender
A – A
D
Clearance
2.5 – 4.5 mm
(0.098 – 0.177 in)
1.5 mm (0.059 in)
E
Surface height
−
1.5 – 0.5 mm
(
−
0.059 – 0.020 in)
1.5 mm (0.059 in)
Trunk lid –
Rear combination lamp
B – B
F
Clearance
3.7 – 7.7 mm
(0.146 – 0.303 in)
3.0 mm (0.118 in)
G
Surface height
−
2.5 – 1.5 mm
(
−
0.098 – 0.059 in)
2.0 mm (0.079 in)
Trunk lid –
Rear bumper
C – C
H
Clearance
4.0 – 8.0 mm
(0.157 – 0.315 in)
—
DLK-226
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID STRIKER : Removal and Installation
INFOID:0000000001722636
REMOVAL
1.
Remove the trunk rear plate. Refer to
.
2.
Remove the bolts, and remove the trunk lid striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installing, perform fitting adjustment. Refer to
DLK-225, "TRUNK LID ASSEMBLY : Adjustment"
.
TRUNK LID HINGE
TRUNK LID HINGE : Exploded View
INFOID:0000000001831348
REMOVAL
1.
Trunk lid assembly
2.
Trunk lid hinge stopper
3.
Trunk lid hinge
4.
Trunk lid stay
5.
Trunk lid striker
6.
Trunk lid lock cover
7.
Trunk lid lock assembly
8.
Trunk lid opener cable
9.
Trunk lid emergency opener lever
holder
10. Trunk lid emergency opener lever
11.
Bumper rubber
Refer to
for the symbols in the figure.
JMKIA1218GB
TRUNK LID
DLK-227
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID HINGE : Removal and Installation
INFOID:0000000001831342
REMOVAL
1.
Remove the trunk lid assembly. Refer to
DLK-224, "TRUNK LID ASSEMBLY : Removal and Installation"
2.
Remove the trunk drip cover. Refer to
EXT-39, "TRUNK DRIP COVER : Removal and Installation"
.
3.
Remove the trunk lid stay. Refer to
DLK-228, "TRUNK LID STAY : Removal and Installation"
.
4.
Remove the trunk lid hinge mounting bolts (body side), and then remove the trunk lid hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check the trunk lid open/close operation after installation.
• Check the hinge rotating part for poor lubrication. If necessary, apply body grease.
• When removing and installing the trunk lid assembly, perform the fitting adjustment. Refer to
225, "TRUNK LID ASSEMBLY : Adjustment"
• After installation, apply touch-up paint (the body color) onto the head of the hinge mounting nuts.
TRUNK LID STAY
TRUNK LID STAY : Exploded View
INFOID:0000000001831349
REMOVAL
1.
Trunk lid assembly
2.
Trunk lid hinge stopper
3.
Trunk lid hinge
4.
Trunk lid stay
5.
Trunk lid striker
6.
Trunk lid lock cover
7.
Trunk lid lock assembly
8.
Trunk lid opener cable
9.
Trunk lid emergency opener lever
holder
10. Trunk lid emergency opener lever
11.
Bumper rubber
Refer to
for the symbols in the figure.
JMKIA1218GB
DLK-228
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID STAY : Removal and Installation
INFOID:0000000001722614
WARNING:
Body injury may occur if no supporting rod is holding the trunk lid open when removing the trunk lid
stay.
REMOVAL
1.
Remove the trunk drip cover. Refer to
EXT-39, "TRUNK DRIP COVER : Removal and Installation"
2.
Insert flat-bladed screwdriver into the gap and remove the trunk lid stay.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check the trunk lid open/close operation after installation.
TRUNK LID WEATHERSTRIP
1.
Trunk lid assembly
2.
Trunk lid hinge stopper
3.
Trunk lid hinge
4.
Trunk lid stay
5.
Trunk lid striker
6.
Trunk lid lock cover
7.
Trunk lid lock assembly
8.
Trunk lid opener cable
9.
Trunk lid emergency opener lever
holder
10. Trunk lid emergency opener lever
11.
Bumper rubber
Refer to
for the symbols in the figure.
JMKIA1218GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст