Infiniti G37 Coupe. Manual — part 229
BCS-34
< COMPONENT DIAGNOSIS >
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
DTC Logic
INFOID:0000000001612402
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000001612403
1.
REPLACE BCM
When DTC [U1010] is detected, replace BCM.
>> Replace BCM.
Special Repair Requirement
INFOID:0000000001612404
1.
REQUIRED WORK WHEN REPLACING BCM
Initialize control unit. Refer to CONSULT-III operation manual NATS-IVIS/NVIS.
>> Work end.
DTC
CONSULT-III display de-
scription
DTC Detection Condition
Possible cause
U1010
CONTROL UNIT (CAN)
BCM detected internal CAN communication circuit malfunction.
BCM
BCS
U0415 VEHICLE SPEED SIG
BCS-35
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
U0415 VEHICLE SPEED SIG
Description
INFOID:0000000001612405
U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from
the ABS actuator and electric unit (control unit).
DTC Logic
INFOID:0000000001612406
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION
1.
Erase the DTC.
2.
Turn ignition switch OFF.
3.
Perform the “Self Diagnostic Results” of CONSULT-III, when passed 2 seconds or more after the ignition
switch is turned ON.
Is any DTC detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001612407
1.
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAG RESULTS
Perform “Self-Diag Results” of ABS actuator and electric unit (control unit) with CONSULT-III. Refer to
.
Is any DTC detected?
YES
>> Repair or replace the malfunctioning part.
NO
>> Replace BCM.
DTC
CONSULT-III display
description
DTC Detection Condition
Probable cause
U0415
VEHICLE SPEED SIG
When the vehicle speed signal received from
the ABS actuator and electric unit (control
unit) remains abnormal for 2 seconds or more.
• ABS actuator and electric unit (control unit)
• BCM
BCS-36
< COMPONENT DIAGNOSIS >
B2562 LOW VOLTAGE
B2562 LOW VOLTAGE
DTC Logic
INFOID:0000000001612408
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION
1.
Erase DTC.
2.
Turn ignition switch OFF.
3.
Perform the “Self Diagnostic Results” of CONSULT-III, when passed 1.5 seconds or more after the ignition
switch is turned ON.
Is any DTC detected?
YES
>> Refer to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001612409
1.
CHECK POWER SUPPLY CIRCUIT
Check BCM power supply circuit. Refer to
Is the circuit normal?
YES
>> Replace BCM.
NO
>> Repair the malfunctioning part.
Special Repair Requirement
INFOID:0000000001612410
1.
REQUIRED WORK WHEN REPLACING BCM
Initialize control unit. Refer to CONSULT-III operation manual NATS-IVIS/NVIS.
>> Work end.
DTC
CONSULT-III display
description
DTC Detection Condition
Possible cause
B2562
LOW VOLTAGE
When the power supply voltage to BCM remains less
than 8.8 V for 1.5 seconds or more
Harness or connector (power supply
circuit)
BCS
B2563 HI VOLTAGE
BCS-37
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B2563 HI VOLTAGE
DTC Logic
INFOID:0000000001612411
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION
1.
Erase DTC.
2.
Turn ignition switch OFF.
3.
Perform the “Self Diagnostic Results” of CONSULT-III, when passed 90 seconds or more after the ignition
switch is turned ON.
Is any DTC detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001612412
1.
CHECK POWER SUPPLY CIRCUIT
Check BCM power supply circuit. Refer to
Is the circuit normal?
YES
>> Replace BCM.
NO
>> Repair the malfunctioning part.
Special Repair Requirement
INFOID:0000000001612413
1.
REQUIRED WORK WHEN REPLACING BCM
Initialize control unit. Refer to CONSULT-III operation manual NATS-IVIS/NVIS.
>> Work end.
DTC
CONSULT-III display
description
DTC Detection Condition
Possible cause
B2563
HI VOLTAGE
When the power supply voltage to BCM remains more
than 18 V for 90 seconds or more
Harness or connector (power supply
circuit)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст