Infiniti G37 Coupe. Manual — part 1352
A/T FLUID COOLER TUBE
TM-261
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
A/T FLUID COOLER TUBE
Exploded View
INFOID:0000000001672282
Removal and Installation
INFOID:0000000001672283
REMOVAL
1.
Remove the engine lower cover with power tool. Refer to
2.
Remove the exhaust mounting bracket. Refer to
3.
Remove the suspension member stay. Refer to
4.
Pull out the A/T fluid cooler hose from the A/T fluid cooler tube. Refer to
1.
Engine assembly
2.
A/T assembly
3.
Copper washer
4.
A/T fluid cooler tube
5.
A/T fluid cooler tube
6.
Bracket
7.
Clip
Refer to
JPDIA0554GB
TM-262
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
A/T FLUID COOLER TUBE
5.
Remove the A/T fluid cooler tube from the A/T assembly and engine assembly.
6.
Remove the stabilizer bar. Refer to
.
7.
Loosen the lower mounting nuts for the engine mounting insulators (RH and LH). Refer to
8.
Set a jack to the engine assembly and slightly lift the engine assembly.
CAUTION:
Do not pull the harnesses, hoses, etc. excessively.
9.
Remove the A/T fluid cooler tube from the vehicle.
CAUTION:
Be careful not to bend A/T fluid cooler tube.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000001672284
INSPECTION AFTER INSTALLATION
Check for A/T fluid leakage and A/T fluid level after completing installation. Refer to
TRANSMISSION ASSEMBLY
TM-263
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
Exploded View
INFOID:0000000001672288
Removal and Installation
INFOID:0000000001672289
REMOVAL
CAUTION:
• When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS)
from the A/T assembly.
• Be careful not to damage sensor edge.
1.
Disconnect the battery cable from the negative terminal.
2.
Remove A/T fluid level gauge.
3.
Remove air cleaner case (RH). Refer to
4.
Remove engine lower cover with power tool. Refer to
.
5.
Remove exhaust front tube and center muffler with power tool. Refer to
.
6.
Remove heat insulator.
7.
Remove rear propeller shaft. Refer to
8.
Remove suspension member stay. Refer to
.
1.
A/T fluid charging pipe
2.
O-ring
3.
A/T assembly
4.
Bracket
5.
A/T fluid level gauge
A.
For tightening torque, refer to
263, "Removal and Installation"
JPDIA0491GB
TM-264
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
9.
Remove exhaust mounting bracket. Refer to
10. Disconnect heated oxygen sensor 2 harness connectors (A).
11. Remove heated oxygen sensor 2 harness (B) from clips (1).
12. Remove bracket (2) from transmission assembly.
13. Remove control rod. Refer to
.
14. Remove crankshaft position sensor (POS) from A/T assembly.
.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front edge magnetic area.
• Do not place in an area affected by magnetism.
15. Remove starter motor. Refer to
.
16. Remove rear plate cover. Refer to
17. Turn crankshaft, and remove the four tightening bolts for drive
plate and torque converter.
CAUTION:
When turning the crankshaft, turn it clockwise as viewed
from the front of the engine.
18. Support A/T assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow
it to collide against the drain plug.
19. Remove rear engine mounting member with power tool. Refer to
20. Remove engine mounting insulator (rear). Refer to
21. Remove dynamic damper. Refer to
22. Disconnect A/T assembly harness connector.
23. Remove air breather hose. Refer to
24. Remove A/T fluid charging pipe from A/T assembly.
25. Remove O-ring from A/T fluid charging pipe.
26. Disconnect fluid cooler tube from A/T assembly. Refer to
.
27. Plug up openings such as the A/T fluid charging pipe hole, etc.
28. Remove bolts fixing A/T assembly to engine assembly with power tool.
29. Remove A/T assembly from vehicle.
CAUTION:
• Secure torque converter to prevent it from dropping.
• Secure A/T assembly to a transmission jack.
INSTALLATION
Note the following, and Install in the reverse order of removal.
: Vehicle front
: Bolt
SCIA8269E
JPDIA0044ZZ
SCIA0499E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст