Infiniti G37 Coupe. Manual — part 558
P1551, P1552 BATTERY CURRENT SENSOR
EC-413
< COMPONENT DIAGNOSIS >
[VQ37VHR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
7.
CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between battery current sensor harness connector and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F1, E3
• Harness for open or short between battery current sensor and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK BATTERY CURRENT SENSOR
EC-419, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace battery negative cable assembly.
10.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000001911025
1.
CHECK BATTERY CURRENT SENSOR
1.
Turn ignition switch OFF.
2.
Reconnect harness connectors disconnected.
3.
Disconnect battery negative cable (1).
4.
Install jumper cable (A) between battery negative terminal and
body ground.
5.
Turn ignition switch ON.
6.
Check the voltage between ECM harness connector and
ground.
Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace battery negative cable assembly.
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E21
3
F102
91
Existed
: To body ground
ECM
Ground
Voltage
Connector
Terminal
F102
91
(Battery current sensor signal)
Ground
Approx. 2.5V
JMBIA0027ZZ
EC-414
< COMPONENT DIAGNOSIS >
[VQ37VHR]
P1553 BATTERY CURRENT SENSOR
P1553 BATTERY CURRENT SENSOR
Description
INFOID:0000000001911022
The power generation voltage variable control enables fuel consumption to be decreased by reducing the
engine load which is caused by the power generation of the generator. The battery current sensor is installed
to the battery cable at the negative terminal. The sensor measures the charging/discharging current of the bat-
tery. Based on the sensor signal, ECM judges whether or not the power generation voltage variable control is
performed. When performing the power generation voltage variable control, ECM calculates the target power
generation voltage based on the sensor signal. And ECM sends the calculated value as the power generation
command value to IPDM E/R. For the details of the power generation voltage variable control, refer to
CAUTION:
Do not connect the electrical component or the ground wire directly to the battery terminal. The con-
nection causes the malfunction of the power generation voltage variable control, and then the battery
discharge may occur.
DTC Logic
INFOID:0000000001734235
DTC DETECTION LOGIC
NOTE:
If DTC P1553 is displayed with DTC P0643, first perform the trouble diagnosis for P0643. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and wait at least 10 seconds.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001911026
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection M95. Refer to Ground Inspection in
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1553
Battery current sensor perfor-
mance
The signal voltage transmitted from the
sensor to ECM is higher than the amount
of the maximum power generation.
• Harness or connectors
(Battery current sensor circuit is open
or shorted.)
• Battery current sensor
P1553 BATTERY CURRENT SENSOR
EC-415
< COMPONENT DIAGNOSIS >
[VQ37VHR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT-I
1.
Disconnect battery current sensor harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between battery current sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 3.
3.
CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between battery current sensor harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F1, E3
• Harness for open or short between battery current sensor and ECM
>> Repair open circuit or short to ground or short to power in harness connectors.
5.
CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between battery current sensor harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F1, E3
• Harness for open or short between battery current sensor and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
Battery current sensor
Ground
Voltage
Connector
Terminal
E21
1
Ground
Approx. 5V
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E21
1
F102
64
Existed
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E21
2
F102
95
Existed
EC-416
< COMPONENT DIAGNOSIS >
[VQ37VHR]
P1553 BATTERY CURRENT SENSOR
1.
Check the continuity between battery current sensor harness connector and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F1, E3
• Harness for open or short between battery current sensor and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK BATTERY CURRENT SENSOR
EC-419, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace battery negative cable assembly.
10.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000001911027
1.
CHECK BATTERY CURRENT SENSOR
1.
Turn ignition switch OFF.
2.
Reconnect harness connectors disconnected.
3.
Disconnect battery negative cable (1).
4.
Install jumper cable (A) between battery negative terminal and
body ground.
5.
Turn ignition switch ON.
6.
Check the voltage between ECM harness connector and
ground.
Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace battery negative cable assembly.
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E21
3
F102
91
Existed
: To body ground
ECM
Ground
Voltage
Connector
Terminal
F102
91
(Battery current sensor signal)
Ground
Approx. 2.5V
JMBIA0027ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст