Infiniti G37 Coupe. Manual — part 827
PRECAUTIONS
IP-9
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
• When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which may
get in the way with cloth.
• When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
• Keep removed parts protected with cloth.
• If a clip is deformed or damaged, replace it.
• If an unreusable part is removed, replace it with a new one.
• Tighten bolts and nuts firmly to the specified torque.
• After re-assembly has been completed, make sure each part functions correctly.
• Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
• Do not use any organic solvent, such as thinner or benzine.
IP-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000001722818
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000001722819
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
Remover tool
Remove clips, pawls, metal clips
Power tool
SIIA0995E
PIIB7923J
PIIB1407E
INSTRUMENT PANEL ASSEMBLY
IP-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
ON-VEHICLE REPAIR
INSTRUMENT PANEL ASSEMBLY
Exploded View
INFOID:0000000001722820
JMJIA0343ZZ
IP-12
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
INFOID:0000000001722821
WORK STEP
When removing instrument panel assembly, combination meter, audio unit, center console take steps in the
order shown by the number below.
1.
Instrument finisher A
2.
Cluster lid A assembly
3.
Steering column cover upper
4.
Steering column cover lower
5.
Steering column side cover (LH)
6.
Steering column side cover (RH)
7.
Steering column mask
8.
Cluster lid A lower bracket
9.
Steering column front lower cover
10. Meter bracket
11.
Knee protector lower
12. Instrument driver lower panel
13. Cluster lid C assembly
14. AV control unit
15. Cluster lid D assembly
16. Center ventilator grille (LH)
17. Center ventilator grille (RH)
18. Glove box assembly
19. Glove box lock assembly
20. Instrument finisher B
21. Instrument lower cover
22. Instrument assist lower panel
23. Instrument side panel (LH)
24. Instrument side panel (RH)
25. Instrument side finisher (RH)
26. Instrument side finisher (LH)
27. Instrument panel assembly
28. Center speaker grille
29. Display unit
30. Display unit bracket
: Clip
: Pawl
: Metal clip
PARTS
INSTRUMENT PANEL
ASSEMBLY
COMBINATION
METER
AUDIO UNIT
CENTER
CONSOLE
Selector/shift lever Knob
[1]
[1]
[1]
Console finisher
[2]
[2]
[2]
Rear upper console assembly
(A/T models only)
[3]
[3]
Coin pocket (M/T models only)
[4]
[4]
Console rear finisher
[5]
[5]
Console mask
[6]
[6]
Center console assembly
[7]
[7]
Cluster lid C
[8]
[3]
Cluster lid D
[9]
[4]
Display unit
[10]
[5]
AV control unit
[11]
[6]
Body side welt LH
[12]
Front pillar garnish LH
[13]
Instrument side finisher LH
[14]
Instrument driver lower panel
[15]
Instrument finisher LH
[16]
Instrument side panel LH
[17]
Steering wheel
[18]
[1]
Steering column cover
[19]
[2]
Combination switch
[20]
[3]
Paddle switch (A/T models only)
[21]
[4]
Knee protector
[22]
[5]
Cluster lid A
[23]
[6]
Meter bracket
[24]
Defroster grille (LH/RH)
[25]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст