Infiniti G37 Coupe. Manual — part 828
INSTRUMENT PANEL ASSEMBLY
IP-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
[ ]: Number indicates step in removal procedures.
REMOVAL
1.
Put selector lever in drive position (A/T models only).
2.
Remove selector lever knob (A/T models only). Refer to
TM-227, "Removal and Installation"
3.
Remove shift lever knob (M/T models only). Refer to
TM-18, "Removal and Installation"
4.
Remove console finisher.
• Remove clips from rear of console finisher (1), and then remove pawl of front.
• Pull console finisher (1) upward to disengage from center console.
• Disconnect harness connectors.
5.
Remove screws (B) of center console front side with screw
driver (A).
Body side welt RH
[26]
Front pillar garnish RH
[27]
Instrument side finisher RH
[28]
Instrument passenger lower cover
[29]
Glove box assembly
[30]
Instrument lower assist panel
[31]
Instrument finisher RH
[32]
Instrument driver lower panel
[33]
Instrument side finisher RH
[34]
Instrument side panel RH
[35]
Instrument panel assembly
[36]
(A)
Console finisher (A/T models)
(B)
Console finisher (M/T models)
: Pawl
: Metal clip
JMJIA0489ZZ
JMJIA0032GB
IP-14
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
6.
Remove rear upper console assembly (A/T models only).
• Slide forward, pull up rear upper console assembly (1), and
disconnect metal clips.
• Disconnect heated seat switch harness connectors.
(with heated seat)
7.
Disconnect auxiliary input jacks connector (A) and power socket
harness connector (B) (A/T models only).
8.
Disconnect console sub harness connectors (A) (M/T models
only).
9.
Disconnect heated seat switch connector (A) (M/T models with
heated seat only).
10. Remove coin pocket fixing pawl using a remover tool (A), and
then remove coin pocket (1) (M/T models only).
: Pawl
: Metal clip
JMJIA0033GB
JMJIA0065ZZ
JMJIA0038GB
JMJIA0286ZZ
: Pawl
JMJIA0034GB
INSTRUMENT PANEL ASSEMBLY
IP-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
11. Insert a deep-well socket wrench (A) to rotate adjusting nut to
loosen cable sufficiently (M/T models only).
Refer to
PB-8, "LEVER TYPE : Adjustment"
.
12. Remove console rear finisher.
• Pull back the console rear finisher (1).
• Disconnect inside key antenna connector (A).
13. Remove console mask.
• Open the console lid.
• Pull up console mask (1) by using a remover tool (C), and disengage pawls.
14. Remove screws (C) of center console rear side, and then remove center console assembly (1).
JMJIA0035GB
: Metal clip
JMJIA0037GB
(A)
Console mask (A/T models)
(B)
Console mask (M/T models)
: Pawl
JMJIA0948ZZ
(A)
Console mounting screws (A/T models)
(B)
Console mounting screws (M/T models)
JMJIA0949ZZ
IP-16
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
15. Remove cluster lid C.
• Remove cluster lid C mounting screws (A).
• Pull back cluster lid C (1).
• Disconnect harness connectors.
16. Remove cluster lid D.
• Remove cluster lid D mounting screw (A).
• Pull back cluster lid D (1).
• Disconnect harness connectors.
17. Remove display unit. Refer to
AV-110, "Removal and Installation"
.
18. Disconnect center speaker harness connector (A).
(with center speaker)
19. Remove screw (B).
20. Disconnect inside key antenna connector (A) and clip (B)
located under audio unit.
21. Remove AV control unit. Refer to
AV-343, "Removal and Installation"
22. Remove body side welt LH. Refer to
INT-14, "Removal and Installation"
.
23. Remove front pillar garnish LH. Refer to
INT-14, "Removal and Installation"
JMJIA0043GB
: Pawl
JMJIA0044GB
JMJIA0045GB
JMJIA0046GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст