Infiniti I35 (A33). Manual — part 72
SAT755J
Removal
NHAT0119
SAT756J
SAT944CA
SAT615E
CAUTION:
When removing the transaxle assembly from engine, first
remove the crankshaft position sensor (POS) from the assem-
bly.
Be careful not to damage sensor edge.
1.
Remove battery and bracket.
2.
Remove air cleaner and resonator.
3.
Disconnect terminal cord assembly harness connector and
park/neutral position (PNP) switch harness connectors.
4.
Disconnect harness connectors of revolution sensor, ground
and vehicle speed sensor.
5.
Remove crankshaft position sensor (POS) from transaxle.
6.
Remove LH mounting bracket from transaxle and body.
7.
Disconnect control cable at transaxle side.
8.
Drain ATF.
9.
Remove exhaust front tube.
10. Remove drive shafts. Refer to AX-9, “Drive Shaft”.
11. Disconnect fluid cooler hoses.
12. Remove starter motor from transaxle.
13. Support engine by placing a jack under oil pan.
I
Do not place jack under oil pan drain plug.
14. Remove center member.
15. Remove rear cover plate and bolts securing torque converter
to drive plate.
I
Rotate crankshaft for access to securing bolts.
SAT947C
16. Support transaxle with a jack.
17. Remove bolts fixing A/T to engine.
18. Lower transaxle while supporting it with a jack.
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REMOVAL AND INSTALLATION
Removal
AT-285
SAT977H
Installation
NHAT0120
I
Drive plate runout
CAUTION:
Do not allow any magnetic materials to contact the ring gear
teeth.
Maximum allowable runout:
Refer to EM-82, “Drive Plate Runout”.
I
If this runout is outside the standard, replace drive plate and
ring gear.
SAT044A
I
When connecting torque converter to transaxle, measure dis-
tance “A” to be certain that they are correctly assembled.
Distance “A”:
14 mm (0.55 in) or more
SAT946C
I
Install bolts fixing converter to drive plate.
I
With converter installed, rotate crankshaft several turns to
check that transaxle rotates freely without binding.
SAT602K
I
Tighten bolts securing transaxle.
I
Tighten LH mounting bracket bolts to the specified torque.
Refer to EM-69, “Removal and Installation”.
I
Tighten center member bolts to the specified torque.
Refer to EM-69, “Removal and Installation”.
I
Tighten rear plate cover bolts to the specified torque. Refer to
EM-14, “OIL PAN”.
Bolt No.
Tightening torque
N·m (kg-m, ft-lb)
mm (in)
1
69.6 - 79.4 (7.1 - 8.0, 52 - 58)
65 (2.56)
2
69.6 - 79.4 (7.1 - 8.0, 52 - 58)
52 (2.05)
3
69.6 - 79.4 (7.1 - 8.0, 52 - 58)
40 (1.57)
I
Reinstall any part removed.
REMOVAL AND INSTALLATION
Installation
AT-286
SAT638A
I
Check fluid level in transaxle.
I
Move selector lever through all positions to be sure that tran-
saxle operates correctly.
With parking brake applied, rotate engine at idling. Move selec-
tor lever through N to D, to 3, to 2, to 1 and to R position. A
slight shock should be felt by hand gripping selector each time
transaxle is shifted.
I
Perform road test. Refer to AT-69.
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REMOVAL AND INSTALLATION
Installation (Cont’d)
AT-287
Components
NHAT0121
SAT833K
OVERHAUL
Components
AT-288
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст