Infiniti I35 (A33). Manual — part 71
Control Cable
NHAT0263
SAT754J
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
SHIFT CONTROL SYSTEM
Control Cable
AT-281
SAT031J
Control Valve Assembly and Accumulators
NHAT0114
REMOVAL
NHAT0114S01
1.
Drain ATF from transaxle.
2.
Remove oil pan and gasket.
SAT327F
3.
Disconnect A/T solenoid harness connector.
SAT995C
4.
Remove stopper ring from terminal cord assembly harness
terminal body.
5.
Remove terminal cord assembly harness from transmission
case by pushing on terminal body.
SAT004F
6.
Remove control valve assembly by removing fixing bolts I, X
and
I
.
Bolt length, number and location are shown in the illustration.
I
Be careful not to drop manual valve and servo release
accumulator return spring.
7.
Disassemble and inspect control valve assembly if necessary.
Refer to AT-314.
ON-VEHICLE SERVICE
Control Valve Assembly and Accumulators
AT-282
AAT279
8.
Remove servo release and N-D accumulators by applying
compressed air if necessary.
I
Hold each piston with a rag.
SAT091J
INSTALLATION
NHAT0114S02
I
Set manual shaft in Neutral, then align manual plate with
groove in manual valve.
I
After installing control valve assembly, make sure that
selector lever can be moved to all positions.
AAT189
Revolution Sensor Replacement
NHAT0115
1.
Remove under cover.
2.
Remove revolution sensor from A/T.
3.
Reinstall any part removed.
I
Always use new sealing parts.
SAT033J
Park/Neutral Position (PNP) Switch Adjustment
NHAT0116
1.
Remove control cable from manual shaft.
2.
Set manual shaft in N position.
3.
Loosen park/neutral position (PNP) switch fixing bolts.
AAT469A
4.
Insert pin into adjustment holes in both park/neutral position
(PNP) switch and manual shaft as near vertical as possible.
5.
Reinstall any part removed.
6.
Check continuity of park/neutral position (PNP) switch. Refer
to AT-108.
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ON-VEHICLE SERVICE
Control Valve Assembly and Accumulators (Cont’d)
AT-283
SAT763J
Control Cable Adjustment
NHAT0117
Move selector lever from the P position to the 1 position. You
should be able to feel the detents in each position. If the detents
cannot be felt or the pointer indicating the position is improperly
aligned, the control cable needs adjustment.
1.
Place selector lever in P position.
2.
Loosen control cable lock nut and place manual shaft in P
position.
CAUTION:
Turn wheels more than 1/4 rotations and apply the park lock.
3.
Push control cable in the direction of the arrow shown in the
illustration by specified force.
Specified force: 4.9 - 9.8 N (0.5 - 1.0 kg, 1.1 - 2.2 lb)
4.
Tighten control cable lock nut.
5.
Move selector lever from P to 1 position again. Make sure that
selector lever moves smoothly.
I
Make sure that the starter operates when the selector
lever is placed in the N or P position.
I
Make sure that the transmission is locked properly when
the selector lever is placed in the P position.
SAT781-C
Differential Side Oil Seal Replacement
NHAT0118
1.
Remove drive shaft assembly. Refer to AX-9, “Drive Shaft”.
2.
Remove oil seal.
SAT782
3.
Install oil seal.
I
Apply ATF before installing.
SAT579K
I
Install oil seals so dimension A is within specification
A: −0.5 mm (−0.02 in) to 0.5 mm (0.02 in)
4.
Reinstall any part removed.
ON-VEHICLE SERVICE
Control Cable Adjustment
AT-284
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст