Infiniti FX35, FX50 (S51). Manual — part 588
PRECAUTIONS
DLN-187
< PRECAUTION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PRECAUTION
PRECAUTIONS
Service Notice or Precautions for Rear Final Drive
INFOID:0000000005249218
• Check for the correct installation status prior to removal or disassembly. If matching marks are required, be
certain they never interfere with the function of the parts when applied.
• Overhaul should be done in a clean work area, it is preferable to work in dustproof area.
• Before disassembly, using steam or white gasoline, completely remove sand and mud from the exterior of
the unit, preventing them from entering into the unit during disassembly or assembly.
• Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them
with a new ones if necessary.
• Gaskets, seals and O-rings should be replaced any time when the unit is disassembled.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If tight-
ening sequence is specified, observe it.
• Clean and flush the parts sufficiently and blow-dry them.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mounting surface; then remove any moisture, oil,
and foreign materials from the application and mounting surfaces.
• Always use shop paper for cleaning the inside of components.
• Never use cotton gloves or shop rags to prevent entering of lint.
• During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or multi-
purpose grease as specified for each vehicle, if necessary.
DLN-188
< PREPARATION >
[REAR FINAL DRIVE: R200]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000005249219
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV40104100
(
—
)
Attachment
Removing side flange
ST36230000
(J-25840-A)
Sliding hammer
Removing side flange
ST3127S000
(J-25765-A)
Preload gauge
Measuring pinion bearing preload and total
preload
KV381054S0
(J-34286)
Puller
Removing front oil seal
ST30720000
(J-25405)
Drift
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
• Installing front oil seal
• Installing pinion rear bearing outer race
KV38107900
(J-39352)
Protector
Installing side flange
ZZA0804D
ZZA0803D
ZZA0806D
ZZA0601D
ZZA0811D
S-NT129
PREPARATION
DLN-189
< PREPARATION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
KV38100200
(J-26233)
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
Installing side oil seal
KV10111100
(J-37228)
Seal cutter
Removing rear cover
KV38100800
(J-25604-01)
Attachment
A: 541 mm (21.30 in)
B: 200 mm (7.87 in)
Fixing unit assembly
ST3306S001
(J-22888-D)
Differential side bearing puller set
1: ST33051001
(J-22888-20)
Puller
2: ST33061000
(J-8107-2)
Base
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.
Removing and installing side bearing inner
race
KV10112100
(BT-8653-A)
Angle wrench
Tightening the drive gear mounting bolt
KV38100300
(J-25523)
Drift
a: 54 mm (2.13 in) dia.
b: 46 mm (1.81 in) dia.
c: 32 mm (1.26 in) dia.
Installing side bearing inner race
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA1143D
S-NT046
SDIA0267E
NT072
ZZA0120D
ZZA1046D
DLN-190
< PREPARATION >
[REAR FINAL DRIVE: R200]
PREPARATION
(J-8129)
Spring gauge
Measuring turning torque
KV40105230
(
—
)
Drift
a: 92 mm (3.62 in) dia.
b: 86 mm (3.39 in) dia.
c: 45 mm (1.77 in) dia.
Installing pinion rear bearing outer race
ST30611000
(J-25742-1)
Drift bar
Installing pinion front bearing outer race (Use
with ST30613000)
ST30613000
(J-25742-3)
Drift
a: 72 mm (2.83 in) dia.
b: 48 mm (1.89 in) dia.
Installing pinion front bearing outer race
ST30901000
(J-26010-01)
Drift
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.386 in) dia.
Installing pinion rear bearing inner race
(J-34309)
Differential shim selector tool
Adjusting bearing preload and pinion gear
height
(J-25269-4)
Side bearing disc (2 Req'd)
Selecting pinion height adjusting washer
Tool number
(Kent-Moore No.)
Tool name
Description
NT127
PDIA0591E
S-NT090
ZZA1000D
ZZA0978D
NT134
NT136
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст