Infiniti FX35, FX50 (S51). Manual — part 607
PREPARATION
DLN-263
< PREPARATION >
[REAR FINAL DRIVE: R230]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Commercial Service Tool
INFOID:0000000005249267
ST30901000
(J-26010-01)
Drift
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.386 in) dia.
• Installing drive pinion rear bearing inner
race
• Installing side bearing inner race
—
(J-8129)
Spring gauge
Measuring turning torque
ST15310000
(
—
)
Drift
a: 96 mm (3.78 in) dia.
b: 84 mm (3.31 in) dia.
Installing drive pinion rear bearing outer race
ST35325000
(
—
)
Drift bar
Installing drive pinion front bearing outer race
ST30621000
(
—
)
Drift
a: 79 mm (3.11 in) dia.
b: 59 mm (2.32 in) dia.
Installing drive pinion front bearing outer race
ST30022000
(
—
)
Drift
a: 110 mm (4.33 in) dia.
b: 56 mm (2.20 in) dia.
c: 46 mm (1.81 in) dia.
Installing side bearing inner race
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA0978D
NT127
S-NT673
S-NT090
ZZA1000D
ZZA0978D
DLN-264
< PREPARATION >
[REAR FINAL DRIVE: R230]
PREPARATION
Tool name
Description
Puller
Removing drive pinion rear bearing inner race
Spacer
a: 60 mm (2.36 in) dia.
b: 36 mm (1.42 in) dia.
c: 30 mm (1.18 in)
Installing drive pinion front bearing inner race
Power tool
Loosening nuts and bolts
ZZA0700D
ZZA1133D
PBIC0190E
REAR DIFFERENTIAL GEAR OIL
DLN-265
< PERIODIC MAINTENANCE >
[REAR FINAL DRIVE: R230]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PERIODIC MAINTENANCE
REAR DIFFERENTIAL GEAR OIL
Inspection
INFOID:0000000005249269
OIL LEAKAGE
Make sure that differential gear oil is not leaking from the rear final drive assembly or around it.
OIL LEVEL
1.
Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Never start engine while checking differential gear oil level.
2.
Install the filler plug with a new gasket on it to the rear final drive
assembly. Tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
Draining
INFOID:0000000005249270
1.
Stop the engine.
2.
Remove the drain plug and gasket from the rear final drive
assembly to drain the differential gear oil.
3.
Install the drain plug with a new gasket to the rear final drive
assembly. Tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
Refilling
INFOID:0000000005249271
1.
Remove the filler plug and gasket from the rear final drive
assembly.
2.
Fill the rear final drive assembly with new differential gear oil
until the level reaches the specified level near the filler plug hole.
3.
Install the filler plug with a new gasket on it to the rear final drive
assembly. Tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
LLIA0068E
LLIA0068E
Oil grade and viscosity
: Refer to
Oil capacity
: Refer to
.
LLIA0068E
DLN-266
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R230]
FRONT OIL SEAL
REMOVAL AND INSTALLATION
FRONT OIL SEAL
Exploded View
INFOID:0000000005249272
1.
Rear cover
2.
Gasket
3.
Filler plug
4.
Bearing cap
5.
Drain plug
6.
Pinion mate shaft
7.
Pinion mate gear
8.
Lock pin
9.
Pinion mate thrust washer
10. Side gear
11.
Side gear thrust washer
12. Side bearing
13. Side bearing adjusting washer
14. Drive gear
15. Differential case
16. Drive pinion
17. Pinion height adjusting washer
18. Pinion rear bearing
19. Collapsible spacer
20. Side oil seal
21. Gear carrier
22. Pinion front bearing
23. Front oil seal
24. Companion flange
25. Drive pinion lock nut
A.
Oil seal lip
B.
Screw hole
C.
Comply with the assembly proce-
dure when tightening. Refer to
: Apply gear oil.
: Apply anti-corrosion oil.
: Apply Genuine Silicone RTV or equivalent. Refer to
GI-16, "Recommended Chemical Products and Sealants"
.
: Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to
GI-16, "Recommended Chemical Products
Refer to
for symbols not described above.
JPDID0289GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст